Did you buy your MJ a gift? Merry Christmas and Happy Holidays

[Htchevyii]

Hope you and your Jeeps get something special for Christmas. 😉 Nothing for the MJ, the BFG MT-03's that I bought a few months ago will have to do! 

[Ωhm]

Okay fellows, time to buy her something.

 

custom - Jeep Comanche MJ Women's Christmas Pajamas - Designed by ChanelKent

[JZLAJeep]

13 minutes ago, Ωhm said:

Okay fellows, time to buy her something.

 

custom - Jeep Comanche MJ Women's Christmas Pajamas - Designed by ChanelKent

Where was this earlier when I needed it?!? 

[89 MJ]

Merry Christmas!

[Pete M]

make sure to get a fire going so the fat man can't pop in and steal your cookies!! 

[Eagle_SX4]

10 minutes ago, Pete M said:

make sure to get a fire going so the fat man can't pop in and steal your cookies!! 

[Htchevyii]

1 hour ago, Pete M said:

make sure to get a fire going so the fat man can't pop in and steal your cookies!! 

 As long as he leaves car parts, he can have 'em! He'd better stay away from my bourbon, unless he leaves me something really good! 

[pizzaman09]

Happy Christmas Everyone!

My MJ is getting a transfer case output bushing and seal for Christmas.

 

My you stay less stuck in the snow than my brother's attempt to blast though the snow in our friends driveway.

[Salvagedcircuit]

On 12/24/2024 at 8:14 PM, pizzaman09 said:

Happy Christmas Everyone!

My MJ is getting a transfer case output bushing and seal for Christmas.

 

My you stay less stuck in the snow than my brother's attempt to blast though the snow in our friends driveway.

 

Hahaha. Awesome. I got some Jeep branded mudflaps for my MJ

[Muncher]

Got mine some notch customs 

[Jeepzahn]

I got my ‘88 4x4 a sister ‘89 4x2 Pioneer. 😆 Brought her home on Christmas Eve after a last minute 9 hour drive to Florida. 

[Htchevyii]

1 hour ago, Muncher said:

Got mine some notch customs 

Nice, I've been eyeing those Notch Customs flares for a while. If I ever move up to bigger tires, I'll probably go that route.

[Htchevyii]

42 minutes ago, Jeepzahn said:

I got my ‘88 4x4 a sister ‘89 4x2 Pioneer. 😆 Brought her home on Christmas Eve after a last minute 9 hour drive to Florida. 

That's a great gift!

[pizzaman09]

43 minutes ago, Jeepzahn said:

I got my ‘88 4x4 a sister ‘89 4x2 Pioneer. 😆 Brought her home on Christmas Eve after a last minute 9 hour drive to Florida. 

Congratulations on the new one!  A last minute 9 hour drive is not trivial.

[gogmorgo]

 

Not really a Christmas present cause I’ve been sitting on these parts basically since last Christmas, but finally and slowly working towards making it all fit. 

 

[Htchevyii]

Ha ha, I feel ya. I do have a front "frame" plate kit and a Mopar rear main seal to install. I'm not got to divulge how long I've been sitting on those parts. 😉

 

I slapped on an Amazon steering brace kit a year or two ago when I saw some cracks starting. It was just supposed to be a temp fix for an upcoming trip. It's time to fix it correctly.

[Car Enthusiast]

Sure did! OGR front bumper will be here on the 7th.

[watchamakalit]

Well I got inspired by this thread. My new Tom woods front shaft will be on its way shortly. I know, I know, it's past Christmas, but hear me out.  The mj is put up for winter storage with the battery disconnected, so the date on the rem will reset. Therefore it won't even know the gift is late.

[WranglerMangler]

On 12/30/2024 at 1:39 PM, Htchevyii said:

I do have a front "frame" plate kit and a Mopar rear main seal to install. 
 

Be sure to get to that frame plate kit before it’s too late! I absolutely annihilated my “frame” on my first MJ because I procrastinated. I don’t see too many beat down or heavy wheeling vids from you guys tho. But if there’s already cracks…. 
 

I’ve found a .22 caliber Bore snake works wonders on the groove in the block. The last RMS I had to do came out in pieces and lots of crud was left up in the groove. 
I had to cut off the brass weight and use a piece of safety wire to fish the rope through then went to town with the bore snake. Cleaned up surprisingly well. 
Keep up the good work buddy! 

 

 

 

 

[Htchevyii]

22 minutes ago, WranglerMangler said:

 

Thanks! I've already changed this one 3 times. I've never had one that I replaced leak again until this one. The engine has a reground crankshaft and I'm afraid that their was excessive wear and polishing to even it out in the RMS area. It the Mopar one doesn't change anything, I'll deal with it until I build a stroker. 

 

We usually don't get too carried away on hardcore stuff on trips. We are usually hundreds of miles from home and alone, so it seems unwise to test the limits. The old MJ does have well over 300,000 miles (swapped  clusters a long long time ago and don't remember). It  belonged to two loggers before I took possession, so it definitely hasn't led an easy life. I doubt that the high speed washboard roads that I often subject it to help things. Hopefully the cracks haven't gotten much worse, we shall see.

[strictlyxjs]

On 12/27/2024 at 8:54 PM, Jeepzahn said:

I got my ‘88 4x4 a sister ‘89 4x2 Pioneer. 😆 Brought her home on Christmas Eve after a last minute 9 hour drive to Florida. 

What's up with that 86 with the strip package in the background it looks like mine. Got any more pics of it? Even wielder that the one in your pic also appears to have the hidden ramsey winch.

[Jeepzahn]

On 1/1/2025 at 11:00 AM, strictlyxjs said:

What's up with that 86 with the strip package in the background it looks like mine. Got any more pics of it? Even wielder that the one in your pic also appears to have the hidden ramsey winch.

That’s my ‘88 short bed Sportruck rocking ‘86 doors and hood. I saved those body panels from a truck being crushed! I love that color scheme. I still need to continue the stripes down the bed.

I used a Bad Dad Fab mount to hide the winch behind a factory bumper.

 

 

Nice looking truck you have! I have a set of Turbines about to go on mine as well. 

[strictlyxjs]

Looks great! 

[Salvagedcircuit]

On 1/2/2025 at 1:51 PM, Jeepzahn said:

 I love that color scheme. I still need to continue the stripes down the bed.

 

That stripe package is worth it's weight in gold.

[Htchevyii]

I kinda copied the theme on my XJ.