Jump to content

Headlights


89 MJ
 Share

Recommended Posts

18 minutes ago, 89 MJ said:

That makes them brighter? Do you know how?

 

in the original setup the current goes from the battery, to the switch and then back to the headlights harness, that lowers voltage a lot, installing a relay makes the headlights get full 14v AND prevents the switch to overheat and catch on fire

Link to comment
Share on other sites

4 minutes ago, omega_rugal said:

 

in the original setup the current goes from the battery, to the switch and then back to the headlights harness, that lowers voltage a lot, installing a relay makes the headlights get full 14v AND prevents the switch to overheat and catch on fire

Ok. Where can I find one of these relays?

Link to comment
Share on other sites

2 minutes ago, Pete M said:

the solution to your problems has been in my signature for a couple years now :D 

Doh!!!

 

16 minutes ago, jdog said:

Thanks!

 

17 minutes ago, omega_rugal said:

autozone? AFAIK there´s no plug and play solution for sale, you must wire it yourself, i would use 2, one for each headlight

Thank you!

Link to comment
Share on other sites

For an inexpensive solution, the Autopals are good at $50 a pair. They have twice the light as stock bulbs. Add in a relay harness and it doubles that. I am using Cibies though. Cibies, Bosch, Hella are quality, but $60-$70 each. I haven't tried the LEDs. 

Link to comment
Share on other sites

9 hours ago, DesertRat1991 said:

 

Truck-Lite LED with Putco harness.

 

Stock low beam:

20190915_211518.jpg.d38b1534054c840117205f53c39afa79.jpg

 

Truck-Lite low beam:

20190915_225923.jpg.29ba5b5240569af6a2549f5643d3c4b5.jpg

Wow! Those a bright!

9 hours ago, MiNi Beast said:

I use a 52" light bar in the woods. In the city I maintain chitty stock sealed beams. 

I can’t do that as I need it to stay legal. 

8 hours ago, derf said:

I run heated Quadratec LED headlights.  They're great all around.

I’ll look into those. 

7 hours ago, ghetdjc320 said:

HID Morimoto Projectors. Nothing compares to a good projector. 

4FFBACB0-AF2E-44EB-96FD-5E5B86830E06.jpeg

 

3509E851-B721-45D8-B690-F89BB32150B6.jpeg

Thanks!

20 minutes ago, 75sv1 said:

For an inexpensive solution, the Autopals are good at $50 a pair. They have twice the light as stock bulbs. Add in a relay harness and it doubles that. I am using Cibies though. Cibies, Bosch, Hella are quality, but $60-$70 each. I haven't tried the LEDs. 

Ok. I’ll check some of those out. 

Link to comment
Share on other sites

I have Grote LED headlamps on my MJ & XJ.   They're great lights and are "sort of" original looking.   I also installed the relay harnesses mentioned above.

 

https://www.amazon.ca/Grote-90951-5-Sealed-Beam-Headlights/dp/B00QB0CCU4/ref=sr_1_6?crid=3CG6IY733G3HB&dchild=1&keywords=grote+led+headlights&qid=1599738133&sprefix=grote+%2Caps%2C181&sr=8-6

Link to comment
Share on other sites

59 minutes ago, PCO6 said:

I have Grote LED headlamps on my MJ & XJ.   They're great lights and are "sort of" original looking.   I also installed the relay harnesses mentioned above.

 

https://www.amazon.ca/Grote-90951-5-Sealed-Beam-Headlights/dp/B00QB0CCU4/ref=sr_1_6?crid=3CG6IY733G3HB&dchild=1&keywords=grote+led+headlights&qid=1599738133&sprefix=grote+%2Caps%2C181&sr=8-6

Thanks!

Link to comment
Share on other sites

Save yourself some dough, the halogens are adequate when you wire in relays. I went a step further and wired mine so that both headlight filaments remain on in high beam mode, I live in the country and I can light up the backroads nicely. There's some H4 conversion assemblies out there you could swap in if your original sealed beams are shot, price is comparable to replacement halogen beams. I went this route with my K1500 since the sealed beams were damaged, got four H4 housings and bulbs for 60 bucks on ebay...

Link to comment
Share on other sites

24 minutes ago, zomeizter said:

Save yourself some dough, the halogens are adequate when you wire in relays. I went a step further and wired mine so that both headlight filaments remain on in high beam mode, I live in the country and I can light up the backroads nicely. There's some H4 conversion assemblies out there you could swap in if your original sealed beams are shot, price is comparable to replacement halogen beams. I went this route with my K1500 since the sealed beams were damaged, got four H4 housings and bulbs for 60 bucks on ebay...

Sounds good. Thank you!

Link to comment
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share

×
×
  • Create New...