KSjeepguy88 Posted October 4, 2013 Share Posted October 4, 2013 Ok so I have been trying to think about how I'm going to lift my MJ. I would like to fit 275-75r17s on 2014 rubicon wheels under my MJ, I would like about 3.5" to 4.5" of lift. I want to do the spring over axle swap in the rear and do 4" lift spring in the front but how much lift will the SOA give me? Help please! This is every thing I should need. Just give me some input, cuz my girlfriend doesn't talk back when I just rumble on about my MJ! Link to comment Share on other sites More sharing options...
AeroNautical Posted October 4, 2013 Share Posted October 4, 2013 I just did an SOA with a 29 spline 8.25, I'd say it gave me about 4 1/2 to 5 inches. I'll add XJ shackles to lower it a bit later on, something to think about. Link to comment Share on other sites More sharing options...
mnkyboy Posted October 4, 2013 Share Posted October 4, 2013 It takes about 6.5" to make the truck sit level. Link to comment Share on other sites More sharing options...
Pete M Posted October 4, 2013 Share Posted October 4, 2013 how much "lift" it gives depends greatly on how saggy your leafs are. Going SOA will net around 5-6 inches of height over what you have now. if your leafs are shot, then you'll need less lift up front to level it out. if they are in good shape, then you'll need more. :thumbsup: Link to comment Share on other sites More sharing options...
kolton Posted October 4, 2013 Share Posted October 4, 2013 Good choice with the IRO products. Like said before, lift the rear and go from there. Be sure to take proper measurements before your lift so that you can adjust to the proper lift that you achieved. Link to comment Share on other sites More sharing options...
AeroNautical Posted October 4, 2013 Share Posted October 4, 2013 6 inches? Wow, my leafs must be saggier than a.... never mind. With the MJ shackles I get about 5 inches max. Link to comment Share on other sites More sharing options...
Timeless Posted October 4, 2013 Share Posted October 4, 2013 Figure the SOA will net about 5" of lift depending on the condition of your current leaf springs. Therefore, you will need taller front springs unless you want a raked stance. Hopefully you or someone you know is a savvy welder.You don't "need" the BPE's or transfer case drop. You need shocks.If your rig is going to be on the street, I wouldn't recommend their OTK steering because it uses heim joints instead of tapered rod ends. JCR has a nice 1 ton steering kit but you will have to ream your knuckles out. The reamer is not exactly cheap. IDK what you're planning on doing, but 1 ton steering on a Dana 30 is pretty overkill. Get a beefier tie rod and call it a day. Link to comment Share on other sites More sharing options...
Pete M Posted October 4, 2013 Share Posted October 4, 2013 6 inches? Wow, my leafs must be saggier than a.... never mind. With the MJ shackles I get about 5 inches max. I replaced my 2wd leafs with a different set of 2wd leafs and gained 2" of height. :( not good when the truck was nice and balanced before. Link to comment Share on other sites More sharing options...
Eagle Posted October 5, 2013 Share Posted October 5, 2013 Assuming a 2-3/4" axle tube and making NO changes other than just flipping from spring-under to spring-over, the flip should generate 5-1/4" to 5-1/2" of lift. If you're doing an axle swap at the same time, and replacing a Dana 35 with a dana 44, Chrysler 8.25", of Ford 8.8", add to that the difference in axle tube diameter between the D35 and whichever axle you're swapping in. Link to comment Share on other sites More sharing options...
HOrnbrod Posted October 5, 2013 Share Posted October 5, 2013 Axle tube diameters: XJ/MJ D35: 2.62" XJ/MJ D44: 2.75" TJ D44: 2.62" Chrysler 8.25: 3.00" Ford 8.8: ?.??" xj D44 axle tube is around 2.75 in dia. and the 35 was somwhere around 2.62 Link to comment Share on other sites More sharing options...
SW86 Posted October 5, 2013 Share Posted October 5, 2013 ive got 6.5 coils up front and its still not sitting level. not a bad rake but not level. swapped 8.25 with stock 4wd leafs, that apparently, werent shot at all. Link to comment Share on other sites More sharing options...
kolton Posted October 5, 2013 Share Posted October 5, 2013 You also need to calculate in the height of your spring perch. Link to comment Share on other sites More sharing options...
87manche1 Posted October 5, 2013 Share Posted October 5, 2013 Also the thicknes of the leafs. Link to comment Share on other sites More sharing options...
carnuck Posted October 10, 2013 Share Posted October 10, 2013 spring pad thickness x 2 (you are moving it from the bottom of one to the top of the other), thickness of the axle tube plus the thickness of the spring pack. This is metric tonne pack on a shortbox with 2200lbs of wet gravel. and empty (below) Link to comment Share on other sites More sharing options...
92tanMJ Posted October 12, 2013 Share Posted October 12, 2013 You could always stay sprung under and get new 3" or 4.5" leaf packs from hellscreek Link to comment Share on other sites More sharing options...
01yellowxj Posted October 26, 2013 Share Posted October 26, 2013 You could always stay sprung under and get new 3" or 4.5" leaf packs from hellscreek $188 for a rear set of 3" springs from hellscreek....... humm makes me think a small 3" as I have 3" OME HD springs in the garage. Will have to research brake lines, shocks, etc.... Anyone running a 3" now? Would a 31" fit well? I also have a set of 4.5" front springs so maybe the 4" would actually be 4.5 over the worn factory leafs..... Is the metric tonne model easy to identify? Link to comment Share on other sites More sharing options...
92tanMJ Posted October 26, 2013 Share Posted October 26, 2013 This is joester1908 's MJ. It has a 3" lift and 31's This is mine stock on 31's. Once I have money I'm getting 4.5" packs from hellscreek and going to run 35s Link to comment Share on other sites More sharing options...
carnuck Posted October 27, 2013 Share Posted October 27, 2013 I have the Metric Tonne rear springs and SOA so it doesn't drop much, even with 3300lbs of gravel in it. Link to comment Share on other sites More sharing options...
AeroNautical Posted October 27, 2013 Share Posted October 27, 2013 I have the Metric Tonne rear springs and SOA so it doesn't drop much, even with 3300lbs of gravel in it. You just stretched the limit for what I thought was capable for these trucks. 3300lbs is ridiculous! Link to comment Share on other sites More sharing options...
mvusse Posted October 27, 2013 Share Posted October 27, 2013 The MT trucks have an advertised payload capacity of 2205 pounds. 3300 is only 50% over. Link to comment Share on other sites More sharing options...
gogmorgo Posted October 28, 2013 Share Posted October 28, 2013 My guess is someone missed the 2 key. I'm pretty sure he's used that pic before in a similar context and said 2200lbs. Link to comment Share on other sites More sharing options...
carnuck Posted October 28, 2013 Share Posted October 28, 2013 This pic is 2200 lbs (parked on a curb left front) One and a half tractor buckets I only had to take the 3300lbs 10 miles. 2 full tractor buckets (it had been raining, so a lot of water poured out when I went up the hill after the scale) Link to comment Share on other sites More sharing options...
mvusse Posted October 28, 2013 Share Posted October 28, 2013 2 full tractor buckets (it had been raining, so a lot of water poured out when I went up the hill after the scale) That sucks. You paid for all that water.... Link to comment Share on other sites More sharing options...
92tanMJ Posted October 28, 2013 Share Posted October 28, 2013 2 full tractor buckets (it had been raining, so a lot of water poured out when I went up the hill after the scale) That sucks. You paid for all that water.... I was thinking that as well ^ Link to comment Share on other sites More sharing options...
carnuck Posted October 28, 2013 Share Posted October 28, 2013 Unfortunately, that's the way it goes. I needed the gravel right then and not after it dried out. I put the Metric Tonne style springs in because I was thinking of using the truck to haul fifth wheel. I'd have to go full float rear axle and then there is beefing up the frame. Decided to pass and go bigger truck (which is why it's for sale now) Link to comment Share on other sites More sharing options...
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now