fiatslug87

OK, three people have contacted me. The order is: 1-bobweiser 2-smithe1811 3-JeepcoMJ I'll get shipping quotes to all of you and the right of first refusal is the order above. Please let me know within a couple of days if you want them so I may notify the next in line. Thanks. I forgot to mention there is some oxidation on these and a little rust on the underside from the bed that will probably buff right out.

I thought I remembered you saying that in another post. :cheers:

I have a set of aluminum diamond plate bed rail caps and tailgate cap for a short bed. If anyone wants to pay shipping from 94534 they’re yours!! There are some plastic shims on the inside rear of the rail to make them fit properly, they also have 2 holes through the top surface where a tool box was attached. I can send more detailed pictures to anyone interested. Image Not Found

It looks like you have everything except for the wing nut that holds down the clip in your last picture and the clip that attaches to the metal piece protruding from the back panel that the handle snaps into. Team Cherokee has this handle clip: http://www.teamgrandwagoneer.com/cgi-bi ... k&catid=95 they also show a wing nut but it looks different than mine but it might work.

You can also run it through this: http://jeep.avtograd.ru/VIN/vin_en.asp

My '90 Sportruck with a 4.0L came stock with P195/75/15 tires :oops:, I bought it new so I'm certain of this. It's even on the window sticker. However, this was on a 2WD.

If you have a real long screwdriver put the tip up anainst various parts of the engine and the handle up to your ear, usually you will be able to trace odd noises.

Is it a Bosch or a Swingline? :rotf:

If you don't want the tire carrier put it in the Classifieds. I remember someone looking for one.

Maybe a helpful hint. To remove the locking ring I used a brass rod (don't want sparks) as a punch and tapped it with a hammer.

Hey mjtjnj, I can send you a PDF of the '87 MJ electrical manual if you want. Just pm an e-mail address. If anyone else wants one just send an address.

Try Spencer at http://www.Jeepsticker.com when you want to purchase them. He has ELIMINATOR stickers. Spence is a friend of mine and a good kid to boot!! Tell him I sent ya!! CW Hey, wait a minute, I sent him!!! ;) :cheers:

The power was mind boggling!!! :roll:

Try Spencer at http://www.Jeepsticker.com when you want to purchase them. He has ELIMINATOR stickers.

By the way, this is stock from the dealer when they replaced my cracked exhaust manifold in ~'93 (under warranty )

Do you have a picture of the 4 panel installed in your truck? Is it a CRL? Did the gasket fit back in easily?

In either 89 or 90 headrests started coming with the bench seats, probably mandated for safety. My '90 Sportruck had headrests, my '88 Pioneer did not have headrests. My '89 Pioneer had buckets so I don't now about that year.

Here's what one of mine looks like.

The info here may help. http://www.comancheclub.com/forums/view ... highlight=

This is from the '87 MJ Electrical Manual: They are the Power Latch Relay, Fuel Pump Relay and the A/C Clutch Relay from front to back.

I can't believe he destroyed what looked to be a perfectly good Eliminator. :cry:

The wiring diagram from the '88 MJ Electrical manual only shows four speakers.

Hey, I thought you didn't like political threads on here!!! :D :rotf:

My 2WD Auto '89 Pioneer has full gauges, bucket seats & a D44 My 4WD Manual '88 Pioneer had gauges without Tach, bench seat & a D35 Both were purchased from the original owners who hadn't done any modifications.

What seal is this? The one that the back of the hood rests against?