Anyone looking for bed-side Patch Panels?

[JENSSEN]

I have searched high and low on all the sites looking for bed repair panels or new bed sides and they are not listed.

 

I have scavenged a few good bedsides at junk yards but would like new panels or repair panels if available and at a reasonable cost ( gotta support 7 jeeps lol)

 

I know this thread is old but are there still panels or and I saving and going glass bulge fenders

[jeepcoma]

I know this thread is old but are there still panels or and I saving and going glass bulge fenders

 

Z&M stopped selling them?

[JWARNE]

Wow!!!!! I havent been so excited and then let down like this since childhood. Read through this whole thread and then the second to last post just crushed me!!!! Ok so beyond the bedside panels does Z&M still sell the rockers and floor pans? please tell me they do. I can patch the bed but those rockers and floor pans are critical

[sinkrun]

Rockers and floor pans from a cherokee work and can be had most anywhere new. Ebay is a good place to look.

[JWARNE]

yeah I have been looking at the rockers off the xj models though these z&m parts just seemed so much more straight forward. thanks for the info sinkrun. I think its just time to bite the bullet and buy myself a donor comanche

[Casper2000]

I just emailed Zack. He still has the parts you just have to email, or call him to order them.

I didnt see them on his site either but tried anyway. Sides are still $160 aside, and shipping is about $150- $200

Not to bad ...

[87MJTIM]

I ordered and receive one last month. $165 freight shipping to 21740 (MD)

[Incommando]

Talked to Zach tonight. He has both sides of the panels and the longer rocker panels in stock.

 

http://stores.zmjeeps.com/rockers-quarters-bed/

[pitbull4x4]

My bed sides were rusted out. I cut it out at good metal and used front fenders for patch panels. Looks good sorry can't post pictures

[Sugarfoot]

If anyone wants to sell the remaining pieces from the PS bed panel from Z&M and they only needed the wheelwell let me know. I need the rear section behind the wheelwell lower half. but will take the full section if you got that too. Or I'll split a PS full panel with someone and cover some of your freight. The closer you are to 78729 Austin TX the better. Anyone traveling from Ohio to Austin?

 

James and Sugarfoot, still around.

88 Red Comanche Pioneer, 4.0 4x4 (stock)

Austin TX

jed101455@gmail.com

[Incommando]

I cut the rust off and used TJ rear flares to cover the larger openings. I also used TJ rear flares on the front to match. I did the cut and fold behind the wheel well. Came out decent

[pyt0725]

hello where can I get this bed quarter panels ,,, my68bird@hotmail.com

[mikekaz1]

2 door Cherokee rear panels work too, just not full length

[scottie2eyes]

Just want to revive this old thread for anyone interested. I just got off the phone with Zach from Z & M Jeeps and ordered both bed side panels to be shipped to the body shop I work with in western Maine. $160 per side, plus $175 for shipping.

[Pete M]

take lots of pictures and start your own thread!  :thumbsup:

[MJfan94]

Does anybody know where to get rear bed corners?

[coathanger37]

Anyone know where to get a good used tailgate or new skin? Also need a new back glass with the rubber weather strip.

[mikekaz1]

Anyone know where to get a good used tailgate or new skin? Also need a new back glass with the rubber weather strip.

the junkyard

[cquinnball]

Does using the rear fenders of a 97+ 2dr work to patch rear wheel well rot?  Or just pre 97?  I know someone parting out a 97+ 2dr. Thank you!