teamsmith Posted September 26, 2014 Share Posted September 26, 2014 Can I just buy the National brand hub assembly from Advanced @ $75 retail ($52 after coupon) and be satisfied that it will work fine or do I need to hunt down a brand name bearing? I can't determine that my bearings have play but something is making a crazy racket like someone is sharpening scissors that gets worse when I turn the wheel so I can only imagine it's the front bearings since it doesn't change when I take it out of gear. Anyway, preference on hub assembly brand? Thanks Link to comment Share on other sites More sharing options...
88whitemanche Posted September 26, 2014 Share Posted September 26, 2014 4wd? I got timken bearings in mine... No problems yet after 3 years.... Link to comment Share on other sites More sharing options...
Jeep Driver Posted September 26, 2014 Share Posted September 26, 2014 Ahhhhhhhhhh..................National is a name brand........Federal-Mogal. Link to comment Share on other sites More sharing options...
Blue XJ Posted September 26, 2014 Share Posted September 26, 2014 National is a good brand. Been around forever. Link to comment Share on other sites More sharing options...
Incommando Posted September 26, 2014 Share Posted September 26, 2014 As long as you stick with a good brand you are OK. Avoid the cheap McParts house ones unless you want to do this again in 12 months Link to comment Share on other sites More sharing options...
91Pioneer Posted September 26, 2014 Share Posted September 26, 2014 Ditto, National is a decent brand. My local auto parts store carries brands like "Nascar" and "Certified". Those are the kinds of parts I stay away from. Link to comment Share on other sites More sharing options...
Minuit Posted September 26, 2014 Share Posted September 26, 2014 The above guys have it right... National, Timken, Centric - I'd use any of those. Link to comment Share on other sites More sharing options...
husky410ohio Posted September 26, 2014 Share Posted September 26, 2014 I have the 4wd drive unit bearing type and I purchased new Timken bearings from Summit racing in Akron, Ohio. It was not instock but they shipped direct to me in a week no extra charge for shipping. I also replaced my U-joint with a good one with grease fitting and rebuilt the brake caliper too. The old wheel bearing inside seal rusted out and fell off when I took it out. Link to comment Share on other sites More sharing options...
ftpiercecracker1 Posted September 27, 2014 Share Posted September 27, 2014 I second the Timken units. Have a little over 2k on my set, I beat my truck like it owes me money and they are still tight as they day i bought them. Link to comment Share on other sites More sharing options...
mvusse Posted September 29, 2014 Share Posted September 29, 2014 Timken is good, as is National. The Autozone Duralast ones are made by Timken, and I believe (but not positive) the Duralast Gold ones are the exact same as Timknen's own. Link to comment Share on other sites More sharing options...
teamsmith Posted September 29, 2014 Author Share Posted September 29, 2014 Timken is good, as is National. The Autozone Duralast ones are made by Timken, and I believe (but not positive) the Duralast Gold ones are the exact same as Timknen's own. thanks. that is good to know. The Autozone Duralast (no gold specified) is about half price of Timken's own. In the product description I see that the Timken is heavier as far as the packaged item goes (by a pound) and has a 3 year warranty vs. the store brand 1 year. I do need to replace the bearings but I'm already way past budget for this truck that was supposed to be a 'hobby.' This will not be a DD and will not be taken off road; you reckon the quality of the Timken branded is worth the $100+ difference (pair) than either Autozone or Advanced private brands? Link to comment Share on other sites More sharing options...
Timeless Posted September 30, 2014 Share Posted September 30, 2014 The question of whether the Timkens (or other higher end and higher priced brands) are a better fit for you will depend on how much you like replacing unit bearings. Personally, I think its a pain in the arse and I'd rather spend the extra money to know I won't have to deal with it for a long long time. And yes, the better bearings are worth it. Link to comment Share on other sites More sharing options...
HOrnbrod Posted September 30, 2014 Share Posted September 30, 2014 ^^ Agree. There was a post by a member a few years back who cheaped out on unit bearings - forget who it was. The "offshore" unit bearing separated and the wheel came off while tooling down the highway. This post had pics showing the separation, so if whomever posted it up reads this, please furnish a link. Link to comment Share on other sites More sharing options...
88whitemanche Posted September 30, 2014 Share Posted September 30, 2014 Here it is.... Lol http://www.youtube.com/embed/8zHBxwwOg6s Link to comment Share on other sites More sharing options...
ftpiercecracker1 Posted September 30, 2014 Share Posted September 30, 2014 Just remember to always avoid C.R.A.P. ( Chinese Replacement Auto Parts) I don't know who came up with that, but he/she deserves a prize. Link to comment Share on other sites More sharing options...
HOrnbrod Posted September 30, 2014 Share Posted September 30, 2014 Here it is.... Lol http://www.youtube.com/embed/8zHBxwwOg6s No, that was not the post I was thinking of. Link to comment Share on other sites More sharing options...
teamsmith Posted September 30, 2014 Author Share Posted September 30, 2014 Fair enough and thanks for the advice. Timken it will be. Link to comment Share on other sites More sharing options...
mvusse Posted September 30, 2014 Share Posted September 30, 2014 ^^ Agree. There was a post by a member a few years back who cheaped out on unit bearings - forget who it was. The "offshore" unit bearing separated and the wheel came off while tooling down the highway. This post had pics showing the separation, so if whomever posted it up reads this, please furnish a link. That was me. I can't find the pictures anymore, though. The problems I was having with unit bearings have been fixed by swapping out the D35 for a HP D60 out of a 1998 Ford F350. The original axle out of my truck now lives happily under my daughter's 96 Cherokee using the 3 year warranty Autozone Duralast Gold unit bearings, Link to comment Share on other sites More sharing options...
HOrnbrod Posted September 30, 2014 Share Posted September 30, 2014 Thanks for posting mvusse. :thumbsup: Too bad you don't have the pics anymore - they were a real eyeopener as I recall. Link to comment Share on other sites More sharing options...
mvusse Posted September 30, 2014 Share Posted September 30, 2014 Found the photos: Link to comment Share on other sites More sharing options...
HOrnbrod Posted September 30, 2014 Share Posted September 30, 2014 That's them. Was the separation due to "questionable quality" unit bearings or something else? I don't remember for sure........ Link to comment Share on other sites More sharing options...
mvusse Posted October 1, 2014 Share Posted October 1, 2014 Don't know what the cause was. I thought I was having problems with the steering as the truck would pull right every once in a while. After pulling over and checking all the steering components three times I decided to ignore it. In hindsight, it was not the steering, but rather the unit bearing locking up. 6 miles later the front corner of the truck dropped down all of a sudden and as I looked to see if I had a clear lane beside me to pull over I saw my tire rolling down the road, no longer attached to the truck. I was surprised how well the truck handled and how stable it was rolling on three tires and skiing on the passenger steering knuckle after the bottom part of the lower ball joint sheared off. Link to comment Share on other sites More sharing options...
daking Posted October 2, 2014 Share Posted October 2, 2014 One of my customers is a Bearings and Seals store. Yea, all they sell. Surprised they make money, but they are busy. sell alot of bearings to factories and warehouses. Any way, I asked the owner, "whats best, what tends to last longer?" Timken was his answer. He sells 100's a week. Link to comment Share on other sites More sharing options...
xjrev10 Posted October 13, 2014 Share Posted October 13, 2014 Holy $#!&! Link to comment Share on other sites More sharing options...
husky410ohio Posted October 15, 2014 Share Posted October 15, 2014 The Timken bearings I used are made in Korea? Link to comment Share on other sites More sharing options...
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now