Jump to content

Big Dan

Members
 View Profile  See their activity

  • Posts

    397

  • Joined

  • Last visited

 Content Type 

Everything posted by Big Dan

  1. Big Dan
    Someone will correct me if I'm wrong, but, the pin out won't be the same. So, no, that cluster won't work with your renix era dash wiring Sent from my Pixel 2 XL using Tapatalk
  2. Big Dan
    Drain plugs. There are generic rubber sets, on Amazon, that you can get. It will be a multi pack and you'll have to see what fits. As far as a specific part number for the OEM plug, someone else will have to chime in. Sent from my Pixel 2 XL using Tapatalk
  3. Big Dan
    Well..that sucks Sent from my Pixel 2 XL using Tapatalk
  4. Big Dan
    Yep, it's just heat distribution Sent from my Pixel 2 XL using Tapatalk
  5. Big Dan
    Yes, I put hose clamps on both ends to ensure a good seal Sent from my Pixel 2 XL using Tapatalk
  6. Big Dan
    I used a 3 inch diameter hose from McMaster carr. It held up well and was still good to go, after 3 years, before I sold that MJ. Sent from my Pixel 2 XL using Tapatalk
  7. Big Dan
    The "pre-heater" hose? Sent from my Pixel 2 XL using Tapatalk
  8. Big Dan
    I suppose it's possible. The part number matched correctly for an XJ, however. Either way, the flange seems to be interference fit. I'm not sure why it would not stay seated, other than a defect. Sent from my Pixel 2 XL using Tapatalk
  9. Big Dan
    Thats what I figured...thanks for the confirmation. For future reference, what is the "technical" term of that item?
  10. Big Dan
    Any ideas as to why this part of the water pump keeps flying off of the shaft? Brand new Mopar pump.
  11. Big Dan
    At the threat of a complete thread hijack - why are the internal slaves so bad with the BA 10/5 and AX15? Most modern manual vehicles use internal slaves and there doesnt seem to be a problem.
  12. Big Dan
    It did I believe that is C317, then. Awesome. Thank you for the help.
  13. Big Dan
    Maybe C317?
  14. Big Dan
    I looked through the electrical manual and couldn't find it. The circled connector is on the cruise control harness (from an 88 4.0)and connects to the engine harness near where the servo would mount. Can anyone clue me in on to what it operates? Sent from my Pixel 2 XL using Tapatalk
  15. Big Dan
    I'm not big on the exhaust sound. I've got an HO exhaust manifold mated to an OE style Walker exhaust. Sent from my Pixel 2 XL using Tapatalk
  16. Big Dan
    He's mentioned that he had a BA 10/5..that means he'll have the .59 pilot bearing ID. Additionally, he said the input shaft, on the AX15, was .75". So, yes, his original post is correct.
  17. Big Dan
    Yes.
  18. Big Dan
    Bump
  19. Big Dan
    I'm in Tapatalk, so I can't see your signature. But, if you have a renix, most of the 91-96 hoses can be used. The evap to filter drier hose I had to buy from jeepair Sent from my Pixel 2 XL using Tapatalk
  20. Big Dan
    [emoji106][emoji106][emoji106] Sent from my Pixel 2 XL using Tapatalk
  21. Big Dan
    I'll take one as well
  22. Big Dan
    Total was $117, from Amazon.
  23. Big Dan
    D35 Sent from my Pixel 2 XL using Tapatalk
  24. Big Dan
    Nickel Copper (cunifer) Sent from my Pixel 2 XL using Tapatalk
  25. Big Dan
    Honestly, it sounds the same as stock. I can't tell the difference when driving. Sent from my Pixel 2 XL using Tapatalk
×
×
  • Create New...