Wrz Posted December 19, 2014 Share Posted December 19, 2014 I bumped this to say I now have made these tilt bezels and can make more to order . 25 $ for a pair plus shipping. See this link for pics and details: http://comancheclub.com/topic/46210-bucket-seat-tilt-lever-bezels/ Need one bucket seat bezel, can't find a picture but it goes around the tilt mech on side of the seat Also need 2 of the clips that hold relay cover on send me a pm if you have any or all of the items thanks Link to comment Share on other sites More sharing options...
NHMJXJ Posted December 20, 2014 Share Posted December 20, 2014 I have a bunch of those in my unicorn saddle bags. :D There's a thread in here where someone was going to have them fabricated in aluminum. Link to comment Share on other sites More sharing options...
sinkrun Posted December 20, 2014 Share Posted December 20, 2014 looks like a project for my buddys milling machine. Link to comment Share on other sites More sharing options...
Keyav8r Posted December 20, 2014 Share Posted December 20, 2014 When you fond those buy up all you can find. You'll get rich selling them on the forum. Color won't matter. BTW - what happened to the aluminum fabrication idea. If I had a milling machine I'd try to make a two piece interlocking design that could be installed without removing the knob. I think it could be done in two to three set-ups. Link to comment Share on other sites More sharing options...
Wrz Posted December 20, 2014 Author Share Posted December 20, 2014 Man i didnt know these were so rare or impossible to find, I'm getting my seats redone and need one without a crack on it to finish it off Link to comment Share on other sites More sharing options...
sinkrun Posted December 20, 2014 Share Posted December 20, 2014 3-D printer would work great also. Link to comment Share on other sites More sharing options...
ScottJeep Posted December 20, 2014 Share Posted December 20, 2014 Are you wanting factory relay cover clips or functional? I have some aftermarket clips that I use. Link to comment Share on other sites More sharing options...
Wrz Posted December 21, 2014 Author Share Posted December 21, 2014 Are you wanting factory relay cover clips or functional? I have some aftermarket clips that I use. As long as they work that's good for me Have a link? Thanks Link to comment Share on other sites More sharing options...
ScottJeep Posted December 22, 2014 Share Posted December 22, 2014 Here is what I have/have used... I usually trim just a bit off the end of the little piece that "locks" up against the cover cause I found they were a bit long. 3 for $12.00 shipped Link to comment Share on other sites More sharing options...
88ComancheMitch Posted December 22, 2014 Share Posted December 22, 2014 I'll have to check my seat in the garage and see if it's there... Link to comment Share on other sites More sharing options...
Strokermjcomanche Posted December 27, 2014 Share Posted December 27, 2014 My neighbor is going to school for 3d printing . I gave him a good seat tilt bezel and he is currently attempting to make one . He said making all of our interior colors would complicate things so I told him make them black . I will post more details as they come . Link to comment Share on other sites More sharing options...
shelbyluvv Posted December 27, 2014 Share Posted December 27, 2014 I'm in for a few if they can be made! Link to comment Share on other sites More sharing options...
Strokermjcomanche Posted December 27, 2014 Share Posted December 27, 2014 I'm in for a few if they can be made! He said they can . It's just making sure they are made to the correct size and shape . There won't be the texture on the surface of them like the factory ones have . I'm debating whether or not to have them be a two piece to slide behind the lever or one like the factory ? Link to comment Share on other sites More sharing options...
johnj92131 Posted December 28, 2014 Share Posted December 28, 2014 Two pieces would let it be installed with out removing the plastic handle on the end of the lever. Just easier to do the replacement. Link to comment Share on other sites More sharing options...
NHMJXJ Posted December 28, 2014 Share Posted December 28, 2014 Where's the line form? I'm in ... one piece, two piece, doesn't matter! Link to comment Share on other sites More sharing options...
HOrnbrod Posted December 28, 2014 Share Posted December 28, 2014 Me too. The one piece bezel would be much easier to make. Removing the drift pin from the lever knob is pretty easy. But either would be fine - hope this works out. And color / texture doesn't matter at all to me. Link to comment Share on other sites More sharing options...
Keyav8r Posted December 30, 2014 Share Posted December 30, 2014 Add me to the list. Would prefer gray, but will take black ones that aren't missing/broken. Link to comment Share on other sites More sharing options...
Rockfrog Posted December 30, 2014 Share Posted December 30, 2014 Add me, add me ... Link to comment Share on other sites More sharing options...
Dillithium Posted December 30, 2014 Share Posted December 30, 2014 and add me! I need two, don't care about color. Link to comment Share on other sites More sharing options...
shelbyluvv Posted December 30, 2014 Share Posted December 30, 2014 See what you started Adam? Link to comment Share on other sites More sharing options...
HOrnbrod Posted December 31, 2014 Share Posted December 31, 2014 See what you started Adam? Now you have to deliver the goods or the consequences will be very severe. :rotfl2: Link to comment Share on other sites More sharing options...
Strokermjcomanche Posted December 31, 2014 Share Posted December 31, 2014 Lol . Like I said its in the works . As soon as I get a finished product I will post an ad in the for sale section . I've got 3 sets of buckets that need the bezels along with everyone else's request . Link to comment Share on other sites More sharing options...
Strokermjcomanche Posted December 31, 2014 Share Posted December 31, 2014 See what you started Adam? Now you have to deliver the goods or the consequences will be very severe. :rotfl2: Are you going to curse me with death wobble? Link to comment Share on other sites More sharing options...
HOrnbrod Posted December 31, 2014 Share Posted December 31, 2014 Had not thought of that. Good idea! :yes: Link to comment Share on other sites More sharing options...
Strokermjcomanche Posted February 26, 2015 Share Posted February 26, 2015 I bumped this to say I now have made these tilt bezels and can make more to order . 25 $ for a pair plus shipping . Link to comment Share on other sites More sharing options...
Recommended Posts
Archived
This topic is now archived and is closed to further replies.