88mjsally

So I bought a 93 Jeep Cherokee 4.0 2wd with a aw4. It only has 113k miles on it and was mainly used as an around town vehicle. The guy I got it from said it would act like it was in neutral after about 20 mins of driving in any gear even when put in reverse. I couldn’t even get it on the trailer before it did it to me. Brought it home and found a bad neutral safety switch so I changed that and no change. Also changed the tps with a known good one. Swapped a different TCM in too with no change. No codes are coming up and there’s no check engine light on. I’m leaning towards just changing the trans but wanted to see if anyone else had any other ideas. I drove it around some today after changing the tps and it idled around fine and I got it into second gear before it just acted like it was in neutral again. Cut it off, waited a few mins and I was able to idle it back to where it was sitting before it only had neutral. When it does this it doesn’t have any gear at all including reverse and unplugging the TCM to shift manually doesn’t work either

So I bought a 93 Jeep Cherokee 4.0 2wd with a aw4. It only has 113k miles on it and was mainly used as an around town vehicle. The guy I got it from said it would act like it was in neutral after about 20 mins of driving in any gear even when put in reverse. I couldn’t even get it on the trailer before it did it to me. Brought it home and found a bad neutral safety switch so I changed that and no change. Also changed the tps with a known good one. Swapped a different TCM in too with no change. No codes are coming up and there’s no check engine light on. I’m leaning towards just changing the trans but wanted to see if anyone else had any other ideas. I drove it around some today after changing the tps and it idled around fine and I got it into second gear before it just acted like it was in neutral again. Cut it off, waited a few mins and I was able to idle it back to where it was sitting before it only had neutral. When it does this it doesn’t have any gear at all including reverse and unplugging the TCM to shift manually doesn’t work either

Updated the look of the grey truck with the jk wheels and spacers that nobody seemed to want. The other tires were getting older and these fit much better. I was even able to take the washers out from under the steering stops. Sadly I found a bad rear axle wheel seal so I need to get that fixed

I should have a good grey one

Little bit of filler work and some paint and it’s pretty much finished. It just needs some seam sealer in the corner and along the bottom seam. Now to start on all the other body work

Key parts rocker is most of the way installed. Just needs a little more welding and grinding

That is a weird coincidence! Mine came from eBay. We still need to meet up sometime if you’re ever going through south carolina

Nope, I’ve been replacing a rocker panel and sold the Comanche I got for parts to a high schooler who is going to fix it up

Found an nos chrome mirror kit with the instructions and hardware as well as a set of ho locks with valet keys

Got rid of the most recent parts jeep so now hopefully I’ll have some time to devote to this truck. Picked up a new to me header panel that’s from a 93 since I want this truck to look like the Comanche they should have made in 93. Going to color match it to the truck and put all the new lights I have for it in it

Finally started to tackle the rust in the floors the other week. Going to get that patched and start getting the truck ready to paint in the fall. Need to start pulling together parts and I need to source a good 3 piece slider

2.8, 2wd d35 truck with buckets and a console as well as a cargo light. Bought it locally for parts but might end up keeping it whole

Only 15😂 A lot more than I could fit in my short bed

Swapped out the starter because the old one had gotten really slow and I already had a new one on the shelf. Did a full tuneup as well with new plugs, msd wires and a cap and rotor. I’ve been driving it to work and it’s been doing well. Even put it to work cleaning out the yard

I have a nice woodgrain trim bezel from a 94 country. I have a working radio too but it has a couple bad pixels on the display

Got the dash back together and everything working including the radio

Trim is back on. Need to put the door panels back in and dash back together before it goes Friday for an alignment

Got a new windshield in finally. Just have to put the trim on. Needs an alignment then I can finally start driving it to work. Might end up putting buckets in it since I have an extra set of brackets and a few extra sets of seats

I should have both the gate and the bezel but I’ll have to look tomorrow

I see 3 a day but all 3 are in my driveway I normally see around 1-2 others around here per month and I’ve sold parts to most of the guys that own them around here

It’s a show truck again with my dads Divco milk truck that we got finished up a couple months ago

It’s broke off in the head and doesn’t leak so it’ll be fine. It’s been like that ever since I got it

New power steering pulley and thermostat housing are in. Put it all back together for the most part. Just need to go get heater hose tomorrow to finish the open cooling swap

Well todays wrenching didn’t exactly go to plan. Started just changing the water pump and ended up changing the power steering pump and pressure hose because they were leaking and I had new ones. Then I tried to take the thermostat housing off and the upper bolt was seized to it so now I need a new one of those. Also need a new power steering pump pulley and a new grill… So it might go back together this weekend when the parts come in