MiNi Beast

$3.38 yesterday, at lunch $.3.55, now $3.83

tie rod ends got here today. :thumbsup: now to get some 1.25 x .25 wall dom to be tapped for the ends. :D

got me my lockouts :D and took the kid to go see Shortiron's little truck. :yes: she thought it was cool after seeing the Monster trucks at van Andel few weeks ago.

Its almost the same then as it is now. Brandon yeah and the say going to be higher then what we have seen before. :ack:

$3.45 unleaded and $3.75 diesel

Well always good to hear. Glad that they work out for you. :cheers:

Should have them knuckles done by now. :brows:

well 1 ton tie rods are bought and being shipped, along with Hy-steer studs and washer things, had to order 1 set of spindle studs as had some bad ones. Now in need of wheel studs and trying to find them some place other then the parts store where they only carry like 2 and they are $3.50 each, then need open lugs on top of that and pick up a set of 1.5" spacers for it as well. And got me a set of lockouts as well and those should be shipped out soon. tomorrow be picking up rest of seals for the D60 and what I can for the D44 as well. helping a buddy swap out his tranny tomorrow so be dealing with that for a bit.

sure you can.. :yes: http://www.knfilters.com/search/promo.aspx

ball joints in and knuckles on :wrench: getting closer... :brows:

D30 out and gone today. LAs and coils out and deliver them later this week. Picked up ball joints for the D44 so time to start putting it back together. Went to 4byFours in Fruitport and made up a set of spring hangers and looked at a few things and will be installing the D44 as soon as I finish putting it together. should be together by next week. and should be going in the following week. the shackle hanger made.... Then with a pic of my K&N filter on my Snorkle that I posted on 4WD's facebook page, I won a little package from them. And the calender has nice ladies on in it. :brows:

Well the D30 is sold and to be picked up on wed, so with that being sold and the LAs sold i should be able to get the last parts for the D44, U-bolts and ball joints and get the steering made up and get it installed under the jeep within the next couple of weeks. :D

them are the great staff of Twisted trails Offroad Park, they put on a good show, even had fireworks again this year.

buddy's jeep....

couple pics from this weekend at the Dog Party. buddy Coppergar caught fire, header pipe separated and caught harness on fire all people were fine but jeep is done under the hood and dash. couple shots or the main scramble area.. video may have to click on pic

new stickers and be riding the piss out of it tomorrow!!!!

For 4-wheel drive :popcorn: same principal applies to 2wd if just swapping out a new hub bearing assembling, just have no shaft to undo.

left side tranny lines. or inlet on the drivers side are on the rad from 97 and newer.

this guys has lots of good info that will help you. :thumbsup:

do you have a c-clip or non c-clip axle?

:agree: it's one thing going through some puddles, but if anything like me, I love river crossings and going in deep water, and deeper the water the more pressure that the water puts on your seals and always best to check or change your fluids after such outings. :thumbsup:

http://www.nagca.com/grandtech/dana30wheelbearing.htm

i can handle the yeast but no promise on the sugar making it from the road trip. :D

just run a separate tranny cooler from the left side. :brows:

yeah down hill cause of the junk @$$ axles I'm using, be fine once I install the leafs and other axles. :yes: