NHMJXJ

Auction ended/expired with "reserve not met", so it will likely be back. Looks like a dealership listing too.

There's proof. This place is full of subject matter experts. I did put the Tcase in neutral and the shaft wouldn't spin. Only had a little daylight left, so I got both rear wheels off the ground. With the wheels able to spin freely, I could hand turn the yoke on the rear end to mate with the new u-joint. I slid the driveshaft in, lined up the u-joint and in it went. This must have been a progressive event because my truck never felt smooth, but it rides absolutely vibration free now.

And another 7 minutes gone. Fun ride though!

LOL Agreeing! I launched the link and replied to the thread without reading another post. I'm thinking $750 is a bargain for that truck.

Thanks for the tip Jeff ... So vicegrips are definitely out then, right? (Kidding!) I called my garage today and they're going to install the U-joints. Dropping the driveshaft off tomorrow morning and will pick it up on my way home. Should be back in action tomorrow night.

I'd buy that in a heartbeat.

Figured I'd go out and take a look ... the tabs on the yoke are intact. Phewww. Thank you all for your help! This site and its members are awesome! :clapping: There's hope for me yet.

Yes, the cup was gone. The OD of the end of the u-joint would have been swimming under that steel strap, if I'd managed to get everything back up. I'll look in daylight. I didn't see any clean, broken metal on anything, but it was dark, I was on my back under the truck with a flashlight in my teeth and my bifocals weren't helping matters.

That's the right tool.

Me thinks the u-joint is junk. Any special tools needed to replace the u-joints?

I dropped the rear driveshaft pulling into my driveway tonight. I'm not a mechanic, but I think I can handle this. I just need some guidance and a few answers. I swiped the following picture from another site, so you have a visual ... What ever covers the end of the U-joint that fits under the U shaped flat steel plate is GONE (which problably explains the nasty vibration I felt right before the drive shaft dropped). I could back out the bolts that hold that plate on by hand. I literally coasted into the end of my driveway. I limped the truck into its spot by putting it in part time 4wd, which brings me to question No.1 ... was that a mistake? Second, I foolishly separated the front of driveshaft from the ... transfer case? Yes? Whatever the doohicky is the front of the driveshaft goes in. It puked about a cup of fluid. I did this because I was trying to align the u-joint and couldn't spin the shaft. I figured if I could just bolt the thing back up, I could yard drive the truck to position it for repair. Question No. 2 ... does the front of the driveshaft just find a seat? It didn't spin when I put it back in. Question No. 3 ... I'm guessing I have to have both rear tires off the ground to line up the new u-joint with the rear end. Yes? help

Some testimonials for stockinteriors.com and other sources here >>> http://comancheclub.com/topic/36733-carpet/?hl=carpet

Ahem ... only skipped one month. Going up in price though. Guess that's a new selling strategy. 8/25/14 http://comancheclub.com/topic/44192-dually-in-houston-3800-obo/?hl=dually 6/13/14 http://comancheclub.com/topic/43418-not-a-bad-deal-for-a-southern-dually-mj-in-tx/?hl=dually 5/19/14 http://comancheclub.com/topic/43180-comanche-dually-houston/?hl=dually 4/19/14 http://comancheclub.com/topic/42828-comanche-dually-in-tx-2750/?hl=dually

It's been listed several times over the past few years. I contacted them and coordinating a time to see it was a hassle for the seller.

It's not a race, so get'r done as you can. :rock on: You may want to hang onto that board from your old seat, 'cause the bench from my truck was a little soft.

It will be for sale forever, unless some fool with more dollars than sense comes along. This was posted here back in October 2013.

Well there went another 8 minutes. :)

Doing my usual Craigslist surfing and happened upon this pic in a "Want Ad" post for a Comanche. Is the guy in the picture a CC member? http://hartford.craigslist.org/wan/4582635555.html

Amphibian DNA ... at least that's how they did it in Jurassic Park. :yes: Want one.

It was a nice day in southern New Hampshire ... warm, dry ... time to paint! Hoped I might get a good day to do a spray in bedliner. Doing it on "the cheap", so I know I'm really just making it pretty, but hey, the is a "clean up" thread. Stocked up. Bought a 6 pack (of Rustoleum Spray in Bedliner). Each can covers 20sf. I had sanded surface rust spots off a while ago and hit it with acetone, then primed the spot.

It's baaaack. http://www.ebay.com/itm/Jeep-Comanche-PIONEER-RESTORED-JEEP-COMANCHE-4X4-13-000-00-INVESTED-L-K-nice-as-they-come-no-reserv-/221534965892?forcerrptr=true&hash=item3394835084&item=221534965892&pt=US_Cars_Trucks#ht_720wt_925

?

Hey! Good lookin' rig. Nice and stout, and doesn't look like it squatted an inch with the 4 wheeler in the back. Have fun!

Baking soda results ... Yucky nooks Clean crannys

So, I looked under the carpet and remedied that! Next order of business is to do Cruiser's tips. I also have a dash cluster that I plan to harvest gauges from to replace the idiot lights. I'd like to keep the existing PRNDL cluster and populate it with the gauges from the donor. I'm sure that's been done before. Links will be helpful!