Wounded_Fighter Posted August 21, 2018 Share Posted August 21, 2018 Anyone ever had to replace the starter relay? I suspect mine to be faulty, right now I'm getting two alternating scenarios. A. - turn key, nothing no dash. Battery tests at 95% with 12.5v. No broken fuses. No loose wires. B. - turn key everything comes up as it should, turn to starter, small humming no crank, everything goes off like someone disconnected the battery. New items, optima red top battery, alternator, starter... (just ordered a set of cables from meanlemons too) Suspect culprit. Link to comment Share on other sites More sharing options...
Wounded_Fighter Posted August 21, 2018 Author Share Posted August 21, 2018 So, side question to go with this, should RockAuto run out of these eventually, or just to make ease of finding/purchasing by making more selection... I found this one that has the diagram on the side of it... I was wondering if it was possible to eliminate the F pin by connecting it to the threaded post? anyone with electrical knowledge have some advice? Link to comment Share on other sites More sharing options...
Pete M Posted August 21, 2018 Share Posted August 21, 2018 for me that scenario always meant a poor connection to the battery. have you cleaned the mating surface between the battery and clamps? Link to comment Share on other sites More sharing options...
Wounded_Fighter Posted August 21, 2018 Author Share Posted August 21, 2018 4 minutes ago, Pete M said: for me that scenario always meant a poor connection to the battery. have you cleaned the mating surface between the battery and clamps? Disconnected, lightly sanded post and connector. no difference. Link to comment Share on other sites More sharing options...
Pete M Posted August 21, 2018 Share Posted August 21, 2018 do you have a multimeter? Link to comment Share on other sites More sharing options...
Wounded_Fighter Posted August 21, 2018 Author Share Posted August 21, 2018 8 minutes ago, Pete M said: do you have a multimeter? yes sir, suggestions? I'm thinking +/- posts, +/bat on relay, and bat/I or bat/g on the relay? correct? Link to comment Share on other sites More sharing options...
Ωhm Posted August 21, 2018 Share Posted August 21, 2018 2 hours ago, Wounded_Fighter said: .. I was wondering if it was possible to eliminate the F pin by connecting it to the threaded post? I've notice that both old and new relays have Pin F. I believe that pin feeds (BAL circuit) the fuel pump during CRANK, bypassing the ballast resistor. Connecting Pin F to BATT (threaded stud) would cause fuel pump to run constantly. Link to comment Share on other sites More sharing options...
Wounded_Fighter Posted August 21, 2018 Author Share Posted August 21, 2018 1 hour ago, Ωhm said: I've notice that both old and new relays have Pin F. I believe that pin feeds (BAL circuit) the fuel pump during CRANK, bypassing the ballast resistor. Connecting Pin F to BATT (threaded stud) would cause fuel pump to run constantly. What about connected to the sol pin? Link to comment Share on other sites More sharing options...
Ωhm Posted August 21, 2018 Share Posted August 21, 2018 Pin F (BAL) is connected to SOL internally. Link to comment Share on other sites More sharing options...
Ωhm Posted August 21, 2018 Share Posted August 21, 2018 I think you just got a bad starter motor by the symptoms posted. Link to comment Share on other sites More sharing options...
Manche757 Posted August 21, 2018 Share Posted August 21, 2018 Worn ignition switch. Contacts making intermittent connections. Wounded see your A and B in first post Link to comment Share on other sites More sharing options...
Wounded_Fighter Posted August 21, 2018 Author Share Posted August 21, 2018 13 minutes ago, Manche757 said: Worn ignition switch. Contacts making intermittent connections. Wounded see your A and B in first post I'll open the column up and take a peek at it. Link to comment Share on other sites More sharing options...
omega_rugal Posted August 22, 2018 Share Posted August 22, 2018 Bad ground from battery to engine (chassis) Link to comment Share on other sites More sharing options...
Jeep Driver Posted August 22, 2018 Share Posted August 22, 2018 1 minute ago, omega_rugal said: Bad ground from battery to engine (chassis) For once I agree with you. :) Link to comment Share on other sites More sharing options...
Wounded_Fighter Posted August 22, 2018 Author Share Posted August 22, 2018 Actually turned out to be the suspected relay. Going to still run more tests to make sure it doesn't happen again for any reason at all... Replaced and runs again. Link to comment Share on other sites More sharing options...
Pete M Posted August 22, 2018 Share Posted August 22, 2018 excellent! Link to comment Share on other sites More sharing options...
Jeep Driver Posted August 23, 2018 Share Posted August 23, 2018 20 minutes ago, Wounded_Fighter said: Actually turned out to be the suspected relay. Going to still run more tests to make sure it doesn't happen again for any reason at all... Replaced and runs again. Where'd you get the relay? Part number? Link to comment Share on other sites More sharing options...
Wounded_Fighter Posted August 23, 2018 Author Share Posted August 23, 2018 9 minutes ago, Jeep Driver said: Where'd you get the relay? Part number? Rockauto Few remaining.... more expensive on Amazon. SR123 Also linked in my build page Found by backtracing the number that was on the originals mount arm. Got lucky I suppose Link to comment Share on other sites More sharing options...
HOrnbrod Posted August 23, 2018 Share Posted August 23, 2018 When that Chinese Airtex relay burns up, get a Mopar relay on Ebay for a bit more $$ HERE. Link to comment Share on other sites More sharing options...
Wounded_Fighter Posted August 23, 2018 Author Share Posted August 23, 2018 5 minutes ago, HOrnbrod said: When that Chinese Airtex relay burns up, get a Mopar relay on Ebay for a bit more $$ HERE. Got my fingers crossed that it doesn't... thanks for the mopar link! I'll revive this when it dies just for the laughs. Link to comment Share on other sites More sharing options...
HOrnbrod Posted August 23, 2018 Share Posted August 23, 2018 14 minutes ago, Wounded_Fighter said: Got my fingers crossed that it doesn't... thanks for the mopar link! I'll revive this when it dies just for the laughs. Hopefully it won't take out anything else when it smokes. Link to comment Share on other sites More sharing options...
Wounded_Fighter Posted August 23, 2018 Author Share Posted August 23, 2018 21 minutes ago, HOrnbrod said: Hopefully it won't take out anything else when it smokes. Ehhhh. I have a little more faith in it than that... Link to comment Share on other sites More sharing options...
HOrnbrod Posted August 23, 2018 Share Posted August 23, 2018 Only raggin' on ya a bit. It'll be fine. Link to comment Share on other sites More sharing options...
Wounded_Fighter Posted August 27, 2018 Author Share Posted August 27, 2018 On 8/22/2018 at 9:37 PM, HOrnbrod said: Only raggin' on ya a bit. It'll be fine. It died again..... Same symptoms as before. Got one from napa to test if it's that part... oddly enough it looks like the exact one I put in... Napa part number AR578 Gonna have to trace wires and start replacing stuff.... Maybe eliminate some of them from the relays battery post... LOL... not a clue what most of them go to. Link to comment Share on other sites More sharing options...
HOrnbrod Posted August 27, 2018 Share Posted August 27, 2018 Yes, you have to clean that mess up and see where those wires go. Most of that stuff is foreign wiring. NAPA's no better than any of the other parts houses, they buy C.R.A.P. from Won Hung Lo too. Grab a regulation Mopar relay HERE . Link to comment Share on other sites More sharing options...
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now