Jump to content

Georgia: '92 4.0 Ho, Ax-15, 2Wd


Recommended Posts

  • Replies 210
  • Created
  • Last Reply

Top Posters In This Topic

  • 4 weeks later...
  • 3 weeks later...

 At this point somewhere around 6K miles/yr.  She gets driven to work 1-2 days each week, junkyard runs, and whenever I need to haul things around.  There have been a few periods where she wasn't driven much due to needed repairs.  The longest period was prior to the trans rebuild.  Not being able to shift into gear when warmed up and running made it very difficult to drive in any kind of appreciable traffic.

 

 

Link to comment
Share on other sites

once upon a time I built a similar thing out of wood beams.  loved it!  except for it didn't move. :(  it was just in the garage.  I had to lift the engine up and then push the whole truck backwards.  lol.  I need to make another, but like yours :D  

Link to comment
Share on other sites

  • 1 month later...

  Been chasing some noises in the front end and also a notable deterioration in handling on the highway.  New track bar helped a lot with the handling.  Time will tell if the popping under the driver's side of the floor pan goes away.  The bushing on the old track bar had really compressed although the rubber still seemed to be in decent shape.

2021 new track bar.jpg

2021 track bar.jpg

Link to comment
Share on other sites

Getting pretty deep into both the noise and the odd handling.  One of the guide pins for the brake caliper was rusted solid and had to be beaten out of the bushing.  Interestingly the pads weren't abnormally worn and the bushing was still in good shape.  It was on the driver's side so another possible source of noise.  I also replaced the front U joints.  The noise is/was an occasional loud bang or pop from the driver's side in low speed, high angle turns (parking lot maneuvers).

 

  Handling is still a bit off, although better.  The steering damper was replaced in 2013 so that might be next.

guide pin.jpg

new u joint.jpg

Link to comment
Share on other sites

  • 2 weeks later...

  I checked the bracket and tightened all the nuts about 1/3 turn.  I'll check the corner of the uniframe for cracks when I have a few minutes 

 

Haven't heard much noise recently but she's been on the highway more than anything.  The handling is no longer scary but still not quite right.  I got the block for the Cutlass back from the machine shop and those idiots didn't check it for cracks.  They should do it as a matter of course but I gave them specific, written instructions to check.  I found the crack when I retrieved the block.  I inspected it prior to unloading from Georgia.  I took it back, argued with them, and made them Magnaflux the area in my presence.  Huge crack

 

 

old block from shop.jpg

magnaflux crack 3.jpg

Link to comment
Share on other sites

  Last Saturday I took Georgia across the mountains to look for a replacement block for the Cutlass.  Regardless of the the seller said this one was not rebuildable.  Locked up tight and looked like it had been sitting in a pond:

 

  Hit a Pull-a-Part on the way back and found a free spinning donor with the right block.  I went back across the mountain yesterday to pull the engine.  Long day and it was quite cold out but got it done.  It was snowing on the way back but the Jeep brought it home, albeit at 45 mph in some spots.  With all that weight in the back of the bed no way I was taking snowy curves at 60-65.  I've put 600 miles on her chasing engines in the past 2 weekends...

 

 

junk engine.jpg

73 cutlass 3.jpg

loaded in Jeep.jpg

cutlass after 2.jpg

Link to comment
Share on other sites

  • 2 weeks later...

Loaded up Olds engine #2 and drove it over the mountain to a different machine shop this week.  The trip back with an empty bed was challenging.  The interstate has a large downhill section with 50-60mph switch backs and she had moderate death wobble on each right hand sweeper with a bump.  Yesterday I did an alignment, had the tires rebalanced, and replaced the steering damper.

 

  The reason toe was out by an even amount is due to the steering box swap.  I'll find out how she drives now but I'm running out of stuff to check.

 

2021 alignment.jpg

new steering damper 2021.jpg

block 2 loaded.jpg

Link to comment
Share on other sites

 

 

Quote

define "bouncy"

Prior to the last tire balance & alignment she'd only start to shimmy/oscillate when excited by a bump when traveling above 60mph, usually on the RF wheel, and more so when in a right handed turn.  The oscillations were longer duration and somewhat violent.

 

  Now the shimmy/oscillation can start when driving on a fairly level surface between 65-70mph.  It doesn't seem to need an external excitation but is of a much lower amplitude.  A bump on the RF wheel and the right handed turn at 55mph still exist but the violence of the event it perhaps 1/3-1/2 of what it was.   The truck seems less stable overall but, when events occur, the severity is less.

 

Link to comment
Share on other sites

@1987Comanche As I read your report from your alignment, it looks like it's still adjusted to a slight toe out? I am pretty sure slight toe in is preferred. You can adjust toe yourself, pretty easily. I would bet if you adjusted so you have about 1/8" of difference between you measurement at the front of your tire and the rear of the tire, you would see an improvement.

 

With an inverted Y steering setup, you need to adjust both the drag link and tie rod, and the tie rod will need to be adjusted twice what the drag link is adjusted. I would start with shortening your drag link 1/4 turn, and the drag link 1/2 a turn.

 

Link to comment
Share on other sites

 

Quote

have you rotated the tires with any change in severity? 

 

  The oscillation at 65-70 mph on level ground seemed to start after the rotate/balance.  The alignment and R&B happened almost back to back so hard to say what percentage can be assigned to each.  I'd thought about going back to Sam's Club to have the tire balance checked.  It wouldn't be the first time I'd had tires balanced incorrectly.

 

 

Quote

With an inverted Y steering setup, you need to adjust both the drag link and tie rod, and the tie rod will need to be adjusted twice what the drag link is adjusted. I would start with shortening your drag link 1/4 turn, and the drag link 1/2 a turn.

 I can certainly give it a try.  I've centered the steering wheel myself a few times by trial & error and, as you've noted, 1/4 turn on the drag link makes a big difference. 

 

Quote

check everything up front for movement while you have someone quickly saw the wheel back and forth.

Haven't done this since replacing the track bar.  Last time I could see the old track bar moving a bit against the bushing.

Link to comment
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share


×
×
  • Create New...