Muncher Posted August 23 Author Share Posted August 23 Also doing some slight hauling tonight. Link to comment Share on other sites More sharing options...
Muncher Posted August 24 Author Share Posted August 24 We have a interior! Carpet did not end up the best because I had no mockup so some areas got cut short but luckily I can cover them up. A pillar peices will stay off for now because ill either replace my dash or paint it. Not sure yet. Link to comment Share on other sites More sharing options...
Muncher Posted August 24 Author Share Posted August 24 Also added a cool old rear view mirror from the 50s or 60s. Found it in a old junk yard does not really work great but its better then nothing and it looks cool Link to comment Share on other sites More sharing options...
Muncher Posted August 24 Author Share Posted August 24 Kinda installed not bolted down yet though looks pretty good not sure how I actually feel about it Link to comment Share on other sites More sharing options...
Muncher Posted September 11 Author Share Posted September 11 Got a bunch of stuff recently. New battery cables installed with a sick nasty relay cover. New air filter and got a arb air compressor for it. Sadly that won't be installed for a while cause I went out and shot my self in the foot by accident 🤦 Link to comment Share on other sites More sharing options...
Muncher Posted September 20 Author Share Posted September 20 Link to comment Share on other sites More sharing options...
Muncher Posted October 12 Author Share Posted October 12 Snapchat-917986626.mp4 Link to comment Share on other sites More sharing options...
Muncher Posted Sunday at 09:52 PM Author Share Posted Sunday at 09:52 PM Oil change done again... went to a wix filter and 15w40 to stop leaks lol. Also did fuel filter spark plugs and cleaned up the cap and rotor. Turns out everything leaks so bad on this motor that I even get oil in the dizzy first time for everything I suppose though. Link to comment Share on other sites More sharing options...
Eagle_SX4 Posted Monday at 12:17 AM Share Posted Monday at 12:17 AM 2 hours ago, Muncher said: Turns out everything leaks so bad on this motor that I even get oil in the dizzy Being you have an 87 there was a TSB for this issue. It is covered by I.S. Note 34E. In short if your distributor is leaking from the vent hole ("A" in Fig. 1) you should replace your distributor. Link to comment Share on other sites More sharing options...
Muncher Posted Monday at 12:36 AM Author Share Posted Monday at 12:36 AM My new truck is actually a 88 Link to comment Share on other sites More sharing options...
Muncher Posted 18 hours ago Author Share Posted 18 hours ago New valve cover gasket did the cruiser 54 tip while I was in there. New oil pressure sensor/coolant temp of course now they both don't work and also my tps i ordered was wrong lol waiting on a new one. Also installed a catch can Link to comment Share on other sites More sharing options...
hgeranium Posted 16 hours ago Share Posted 16 hours ago 1 hour ago, Muncher said: New valve cover gasket did the cruiser 54 tip while I was in there. New oil pressure sensor/coolant temp of course now they both don't work and also my tps i ordered was wrong lol waiting on a new one. Also installed a catch can Which catch can did you use? That looks great Link to comment Share on other sites More sharing options...
watchamakalit Posted 11 hours ago Share Posted 11 hours ago 5 hours ago, hgeranium said: Which catch can did you use? That looks great I would like to know also. Link to comment Share on other sites More sharing options...
Muncher Posted 2 hours ago Author Share Posted 2 hours ago 14 hours ago, hgeranium said: Which catch can did you use? That looks great Its just a dorman catch can from autozone or any local parts store kr was expensive but thats the price I pay when I'm impatient and hate ordering online lol. Of course I deleted the ballast resistor and used that spot to bolt it up and bent the bracket around the body right there. Also moved the egr thing over to the ground off the harness Link to comment Share on other sites More sharing options...
hgeranium Posted 2 hours ago Share Posted 2 hours ago 22 minutes ago, Muncher said: Its just a dorman catch can from autozone or any local parts store kr was expensive but thats the price I pay when I'm impatient and hate ordering online lol. Of course I deleted the ballast resistor and used that spot to bolt it up and bent the bracket around the body right there. Also moved the egr thing over to the ground off the harness That’s a great idea to put it where the ballast resistor is. Ive fully removed both that and my EGR solenoid so that makes sense Link to comment Share on other sites More sharing options...
Muncher Posted 2 hours ago Author Share Posted 2 hours ago Just now, hgeranium said: That’s a great idea to put it where the ballast resistor is. Ive fully removed both that and my EGR solenoid so that makes sense Did you fully delete your egr? Link to comment Share on other sites More sharing options...
hgeranium Posted 2 hours ago Share Posted 2 hours ago Just now, Muncher said: Did you fully delete your egr? I don’t have it hooked up but the EGR valve itself is still there with a vacuum cap on it. The vacuum lines on the intake manifold stacked I just have routed to each other with a short C shape hose. I want to delete the whole valve at some point but I’m not in a position to make a block-off plate right now Link to comment Share on other sites More sharing options...
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now