SchneiderFishing Posted March 13, 2009 Share Posted March 13, 2009 Hello All! Just bought my 1st Comanche (4th Jeep) a couple weeks back. Had to spend a bit of money getting it up to California smog standards. It's running good now. It's a 4.0 4wd Pioneer automatic (column shift). The thing is I miss my morning coffee. Anybody got any good ideas foe cup holders? Link to comment Share on other sites More sharing options...
Windowsrookie Posted March 13, 2009 Share Posted March 13, 2009 You can get an aftermarket center console thingy like I have. Link to comment Share on other sites More sharing options...
SuperWade2 Posted March 13, 2009 Share Posted March 13, 2009 Hello All!Just bought my 1st Comanche (4th Jeep) a couple weeks back. Had to spend a bit of money getting it up to California smog standards. It's running good now. It's a 4.0 4wd Pioneer automatic (column shift). The thing is I miss my morning coffee. Anybody got any good ideas foe cup holders? Welcome Robert... Where about's on the Left Coast you located? You have bench or bucket seats...I swapped my Bench for buckets at added a Cherokee full console that I got from one of the guys on here...There is a screw on holder that goes above where the ebreak handle would be (on a Cherokee)...Honestly it's not great...more like a place to set the cup, but I still end up holding it there if I'm going around a corer or over bumps. Link to comment Share on other sites More sharing options...
dakal Posted March 13, 2009 Share Posted March 13, 2009 i have one i will donate for $1.22 plus freight Link to comment Share on other sites More sharing options...
ComancheKid45 Posted March 13, 2009 Share Posted March 13, 2009 I just have a can coozie between my bench seat and some CDs....it works Link to comment Share on other sites More sharing options...
87mjdriver Posted March 14, 2009 Share Posted March 14, 2009 DUCT TAPE 1. buy new roll 2. Unwrap roll 3. slap it down on what ever fabric that is where you want the "cup" to be waa la! I used to have two rolls one stuck to each floor board in front of the seats Link to comment Share on other sites More sharing options...
james750 Posted March 14, 2009 Share Posted March 14, 2009 I use a little $5.00 thing I got at o'reillie's a while back, it used to be bolted to the floor, but when I set large cups down they would get caught on the ashtray and spill the cup, so I moved it so that it is now wedged between the bench and mini console. Supposing you don't have a mini console. You could bolt it down anywhere on the hump you like. It is an easy 5 minute job. Link to comment Share on other sites More sharing options...
SchneiderFishing Posted March 17, 2009 Author Share Posted March 17, 2009 Thanks guys. I've been avoiding the 'on the center of the seat' thing. I was hoping to find something that would go in the center by the 4wd shifter. I have a bench seat just like the ones in the pictures above. I live in Temecula, CA along 1-15 North of San Diego. Thanks for the heads up on o'reillie's. I'll check them out. Link to comment Share on other sites More sharing options...
shelbyluvv Posted March 17, 2009 Share Posted March 17, 2009 Check out Page 2 of my build thread. I cut a 97+ console in half ahd it left me with only one cup holder. But, that is better than nothing right? Link to comment Share on other sites More sharing options...
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now