88mjsally

I have one for sale

It’s been a little while since I’ve done anything to my truck other than use it to haul things around. I pulled the bumper off yesterday to replace it with a new one and install the front skid plate I got. I also redid my lower radiator support with some tubing I found in our shop. I got the tow hooks on today and trimmed the air dam so they would fit but I need to get a few more of the nut clips that hold the bumper on before I can install it. The bumper is brand new and was $50 shipped to my door. The tow hooks came from a guy on Facebook and the skid cane from a 4wd shop in the upstate. It looks much better up there and I also am going to install a fan shroud and bigger fan this week after the truck got a little hot sitting in traffic

Thank you! I wasn’t sure if I qualified or not

I’m out of harness pigtails at the moment but I hope to get more sometime this week so I can get another batch made

The two plugs (male and female) plug in between the factory Jeep mj taillight wiring harness. Then I solder in a flat 4 trailer wiring plug so you can plug in trailer lights. If you’d like me to make a custom one for you that uses the newer 9 pin connector for trailer brakes then I can. You’d just have to run a couple of the wires to your brake controller

These harnesses plug into the factory rear taillight wiring connector and allow you to plug in trailer wiring without hacking up the factory harness

I have one more ready to go in a flat rate box and I have parts to make 5 more I think

This is a junkyard truck I found about a year ago but I went back today and got the VIN. The yard it’s at is more of a full service yard and he is very expensive. I’m kinda guessing on the year but I think it’s an 87. It’s a column shift auto 2wd 4.0. I’ve grabbed most of the good parts off of it already

I have a pair of tan mj kickpanels if you still need them

All of them are tested and ready so I’ll be sending everyone that wanted one a message

I got 9 finished today I just need to test them tomorrow and then wrap them in electrical tape

I have a tan one for sale from an xj but it can be used in a comanche with a slight modification

I went back yesterday to get those bezels however I got there and they were both missing chunks so I didn’t grab them. I see them on occasion so I’ll keep an eye out for more

I just got the parts to make 9 more of these so I’ll be working on them this week. I have enough trailer harnesses to make 14 but I need to get more Cadillac connectors from another junkyard

I’ll go back there this week and grab them since I need to go get a few other things too

I know where a pair is in a junkyard near my house if you want me to try and grab them for you. They looked to be intact last time I was there but I never remember to grab things like that

I just ordered the parts to make 6 more harnesses so I’ll have more made early next week. $40 shipped for one, $70 shipped for two and $100 shipped for 3.

I’m kinda thinking about a mj tailgate with a wood frame and a piece of glass over the top then I can display the emblems in the inset area of the tailgate

I have a pair of black flares I would sell. $100 plus shipping on the pair

Yes I can make you a deal if you buy 3

Yea they work very well. One of my friends told me about them and I’ve been using them for a little while with no real issues

I can get the parts to make another one if you want one

I just think it’s cool how many different emblems there are for jeeps and others. Someday I’ll figure out a way to display all these either in a case or on my wall but for now I just like finding them and looking at them. These are just the Jeep ones but I have a drawer of other ones too

I have the parts to make one more if you want it then I can make it today or tomorrow and ship it Monday morning for you

I’ve been driving the truck a good bit and recently had to fix a steering intermediate shaft issue. I swapped in a tilt column from an 87 a little while ago and the intermediate shaft I had was too short and all the ones I could find were too short. I ended up getting a 83-86 shaft that has two plastic pins that keep it from collapsing and drilling out those pins. I then made it the correct length and drilled and tapped the shaft for two set screws to hold it all together