lower jeep

thanks that helped alot

that from front to back?

could any body tell me antidisestablishmentarianism wires go to each injector i checked the hynes maunal but no luck the wire colors are wrong or not there its a 89 4.0 auto thanks

would it be good to get adjustable still for a 2 wheel drive? and what is the length for the non-adjustables compared to lift height?

ok this might sound weird but has any one put a 4linked grand cherokee rear axle in their mjs? how hard was it to do and is it worth it?

the winch maker use to make a lowering kit for the comanches years ago, i found one at a little truck shop in canada like 4 or 5 years ago gave me a drop 2" drop all the way around and handled great look up my project "my lowered jeep", i used a 4" steel block and xj shacklesto give me a nice level look with the bump stops removed in the rear pm me if your interested for the front springs

so i started my truck up yesterday to start working on it again started just fine backed it up, turned it off to switch gears (need to bleed to clutch) then put it in 1st to move it into the garage and nothing on power to anything no power to my aftermarket fuse panel no lights no power to my air compressor for the air ride , i checked the battery just fine, replaced with a differnt battery, and nothin made sure all the wires were hooked up right no fuses were blown the battery wires looked fine, then checked to see if i had a good ground with a test light (from the + battery post to the body) and had power but couldnt find a dvom to see how much power i actually had but both batterys were just takin off the trickle chargers any body know what is wrong or had the same problems???????? thanks

i just got a 97+ front bumper and using a older front end, antidisestablishmentarianism did you guys do cut the front fenders or cut the bumper end caps to fit around the fenders? thanks lower jeep

ok you guys blocked off the return line with what? i asked my parts guy and he said that they offered nothing to block off a brake line so my question is what did you guys do to block off the return line? thanks

if it was inside the truck while you were welding or within a few feet of the welder it is more than likely junk now sorry to tell you that but its because of the tig emits high freency waves that will destroy just about any thing that uses some kind of magnetics in it hope this makes sense

hey eagle is your camper fiber glass or alumiun and how does it match up on the sides i have a ranger camper shell and it doesnt fit that well its shorter and not as wide at the top as the cab of truck got any pics? thanks lower jeep

ok so I'm putting the interior back in the truck tried the lights before the gauges were in the lights worked that i had hooked up (just the front lights and a few interior lights) then i put the gauges in and connected up the rear lights and now i have no lights. i checked to make sure that i have power to every thing and i do but i have no grounds the ground is connected in the back on the bed but still no lights and it seems to be on the corner lights that i have power to both sides of the connector has any one have this problem before and please help!!! Thanks lower jeep

i got a set of fenders and grill suround form them, paid like $180 i ordered them through there web site, fit is ok had to do some fiting but there not bad for there price and shiping was fast, had them 3-4 day after i ordered them

ok finishing up putting my mj back together but got a question on the starter motor the pos. form the battery goes to the starter on the one post and the 4 ga. wire that comes form up by the coil goes to the same post right? thanks

yhea i have a lowered jeep rear is bagged and the front is on a set of rare lowering springs that i found in canada the rear sits on the ground check out the my lowered jeep under projects

i have found that a 86-96 dodge dakota rollpans are about 1 inch on each side and you have to cut an like 3/8" out on the top mount to get it to fit against the out side of the bed and you can find them for like maybe $70 for a fiberglass one and i think that JC Whitney has a roll top bed cover that is made for the comanches its a hard cover that is made out of alum. and is covered with vinal that sits inside the bed rails but they want 600 -700 dollars for it here are a few options for you that i have found in searching for parts for my truck

here's some pics of my truck now aired up then aired down with bed not bolted down need to cut out the wheel wells on the bed

o the welder is a 115 lincoln welder

well i got the brakets welded on i had a really bad night that nite the next day i went through and checked ever thing over and had polariaties switch for gas less wire (can't think of what the wire is called right now)

pics will be up tomarrow depending on weather have the 4 link welded in and the bag mounts and bags installed just have to air it up and push it out of the garage :D

no offense taken but I'm ICAR certified welder but is the D35 rear end tubes cast or just really thick steel?

to answer a few question ive seen the front is lowered by a old set of Warn winch springs. i found them in Canada over 3-4 years ago brand new i don't know where you can find them at any more ive done research on these but couldnt find any thing about them. My jeep right now is half way torn apart waiting to get put back together after a new paint job it is know a bright green with a soon to been flat black hood and Dodge Duster style stripes on the sides the rear is getting air ride put onto it slowly so far i have the 8 inch c notch welded in and will be welding the 4 link in soon so the truck will lay the frame on the ground will have pics as soon as the 4 link gets put in thanks for the intrest

so i was welding brackets on my rear axle for my 4 link and the welds would not hold the axle is all bare steel, i need help what should i do to get it to hold, heat the axle up before welding the brackets on or what? thanks for the help

i have found lower dash panels with speaker out of XJs they look like tweeters in each side or maybe like 1.5"- 2" speakers.