comanche13 Posted May 1, 2009 Share Posted May 1, 2009 found out yesterday that my track bar bushing is worn out and when i turn it makes a kinda pop or hitting sound i can see where it is is it still safe to drive until i find a new bushing? Link to comment Share on other sites More sharing options...
vaquaro Posted May 1, 2009 Share Posted May 1, 2009 found out yesterday that my track bar bushing is worn out and when i turn it makes a kinda pop or hitting sound i can see where it is is it still safe to drive until i find a new bushing? Park it ! Phone NAPA ,they stock a track bar complete replacement @ about $100 ? ( the bushing kit may not resolve the issue completely ) :cheers: Link to comment Share on other sites More sharing options...
Geonovast Posted May 1, 2009 Share Posted May 1, 2009 You can drive it to the extend of moving it around the driveway, yard, etc. I wouldn't take it over 20 mph. If it's just the bushing on the axle side, you should be able to replace it. If the TRE on the frame side has any play in it whatsoever, you're going to want to replace the entire trackbar. IIRC most aftermarket adjustable ones will run you about the same price as a stock one. Adjustable one=replaceable TRE so you shouldn't need to replace the bar again unless you bend it. Link to comment Share on other sites More sharing options...
comanche13 Posted May 1, 2009 Author Share Posted May 1, 2009 well it only makes the sound when i acually turn the wheels fast but when i try to move it when its just sitting there it does nothing i can't budge it EDIT its when i turn the steering wheel when i can hear it and when I'm on bumpy roads which is what my town is pure pot holes Link to comment Share on other sites More sharing options...
dakal Posted May 1, 2009 Share Posted May 1, 2009 it could be your life if you drive it! :yes: Link to comment Share on other sites More sharing options...
Hawk Posted May 1, 2009 Share Posted May 1, 2009 Don't take the chance. I'd suggest just getting a new aftermarket unit. Link to comment Share on other sites More sharing options...
comanche13 Posted May 1, 2009 Author Share Posted May 1, 2009 man this sucks cause I'm hoping to get a lift kit soon so now i have to spend more on something i might only use for 2 months Link to comment Share on other sites More sharing options...
Comanche County Posted May 1, 2009 Share Posted May 1, 2009 Are you sure the bushing is wore out? Its common for them to come loose and make that popping sound. Mine was doing the same, I just tightened the heck out of it on the fram and axle ends and its fine. Link to comment Share on other sites More sharing options...
comanche13 Posted May 1, 2009 Author Share Posted May 1, 2009 mine has a castle nut on the top with a cotter pin is that what your telling me to tighten or does the bracket bolt to the frame? Link to comment Share on other sites More sharing options...
Geonovast Posted May 1, 2009 Share Posted May 1, 2009 There's 4 bolts holding the bracket to the frame. Two go in through the side behind the spring, and the other two go up from the bottom. First time I replaced one of those brackets I used three original bolts and a new one, but I didn't get a lock washer for the non-flanged bolt and it worked loose, causing DW. I'd make sure they're tight. Oh, and they should be 18 mm. Link to comment Share on other sites More sharing options...
comanche13 Posted May 1, 2009 Author Share Posted May 1, 2009 just went out any tried to tighten there as tight as there ever going to be already Link to comment Share on other sites More sharing options...
Geonovast Posted May 1, 2009 Share Posted May 1, 2009 A good way to see what's loose is jack up the axle enough to get both tires on the ground, and have someone turn the wheel while you watch for any slop. Link to comment Share on other sites More sharing options...
comanche13 Posted May 1, 2009 Author Share Posted May 1, 2009 thats what i did yesterday and when i stuck a screwdriver up to the track bar and put my ear to the screw driver and got my gf to turn the wheels it made tha sound its a good way to amplify the sound to pin point haha Link to comment Share on other sites More sharing options...
mvusse Posted May 1, 2009 Share Posted May 1, 2009 Usually it's the hole in the bracket on the frame end that gets elongated. A new track bar will not solve this. Tightening the castle nut will work for a while, but is not a permanent fix. The problem will come back. If this is your problem, get a "new" one off a Cherokee in a junk yard. While you're under your truck, have somebody else move the steering wheel. Link to comment Share on other sites More sharing options...
comanche13 Posted May 1, 2009 Author Share Posted May 1, 2009 i can also see the track bar bushing kinda move when i turn the steering wheel I'm going down today to pick up a whole track bar for 90 dollars Link to comment Share on other sites More sharing options...
vaquaro Posted May 2, 2009 Share Posted May 2, 2009 i can also see the track bar bushing kinda move when i turn the steering wheel I'm going down today to pick up a whole track bar for 90 dollars Good idea :thumbsup: Link to comment Share on other sites More sharing options...
CWLONGSHOT Posted May 2, 2009 Share Posted May 2, 2009 As mentioned, a new TB is a good idea. But while its off have a good look at the hole at the axle and at the frame. BOTH should be perfectly round. If the AXLE end is oblong, a good thick GRADE 8 WASHER can be welded in to repair. If the FRAME end is oblong, a replacement is in order. CW Link to comment Share on other sites More sharing options...
maddzz1 Posted May 2, 2009 Share Posted May 2, 2009 Do you have alot of play in the steering wheel? If so its probally the bracket. Mine keeps coming loose (the castle nut) because the bracket hole isnt round anymore. I have to replace it on Monday (if it don't rain). It has been this way for a while. If I tighten it down it drives like a new truck. Rockauto has a replacment tracbar for like $35, and you can get the bracket for like $25 at a junk yard if it is the bracket. Link to comment Share on other sites More sharing options...
deziped Posted May 2, 2009 Share Posted May 2, 2009 If its the bracket on the axel thats worn out you can have the holes welded shut and redrill the bracket with the proper size holes. Then put in a new bushing & bolt. Link to comment Share on other sites More sharing options...
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now