big66440 Posted September 14, 2016 Share Posted September 14, 2016 My fan hub bearing is growling and has some play, I really don't want to grab one from the JY if I can avoid it. I've spent a few hours looking through different threads on the net that show the bearing alone CAN be replaced. I have actually gone out to buy one of the NSK Part numbers ( 885586) that people claim can be used as a replacement but the OD of the new bearing seems too big to be pressed into the AC bracket, my original bearing measurement from the rear of the AC bracket is .940" if I'm not mistaken. There is a second NSK # that people claim will fit ( NSK 665325) that I cannot find any information on or someone that even sells it, can any one of you guys help me figure this out? or have any information on the NSK 665325 bearing number ? Thank you all Link to comment Share on other sites More sharing options...
cruiser54 Posted September 14, 2016 Share Posted September 14, 2016 Have you gotten the actual number off the existing bearings? Link to comment Share on other sites More sharing options...
big66440 Posted September 14, 2016 Author Share Posted September 14, 2016 All I can see is "325 R " and the end of the shaft, so I'm assuming it's going to be the 665325?. Based on the info I've seen on the net the bearing type is called a " integral bearing shaft " similar to what's used on water pumps so the bearings alone cannot be replaced. Link to comment Share on other sites More sharing options...
cruiser54 Posted September 14, 2016 Share Posted September 14, 2016 Got any water pump rebuilders in your area? Link to comment Share on other sites More sharing options...
big66440 Posted September 14, 2016 Author Share Posted September 14, 2016 Nope, I'll see if contacting companies that specialize in bearings online will get me anywhere. Link to comment Share on other sites More sharing options...
cruiser54 Posted September 15, 2016 Share Posted September 15, 2016 Nope, I'll see if contacting companies that specialize in bearings online will get me anywhere. How far are you from Phoenix? Link to comment Share on other sites More sharing options...
HOrnbrod Posted September 15, 2016 Share Posted September 15, 2016 The problem isn't the bearing; it's how to press it out. It's a common bearing - check out NAXJA. There are tons of threads on this topic, but I've yet found one where someone actually pressed out and replaced the bearing successfully. Link to comment Share on other sites More sharing options...
cruiser54 Posted September 15, 2016 Share Posted September 15, 2016 These guys did an Alfa Romeo water pump for me. http://www.kelloggautomotive.com/ Someone in California: https://egge.com/info/water-pump-rebuilding/ Link to comment Share on other sites More sharing options...
big66440 Posted September 15, 2016 Author Share Posted September 15, 2016 Nope, I'll see if contacting companies that specialize in bearings online will get me anywhere. How far are you from Phoenix? About a 5 1/2 hour drive, I was able to find a company that had it in stock its called locateballbearings.com. I placed an order and I should probably be receiving it the beginning of this coming week. I will keep you guys posted on the progress. Link to comment Share on other sites More sharing options...
big66440 Posted September 15, 2016 Author Share Posted September 15, 2016 These guys did an Alfa Romeo water pump for me. http://www.kelloggautomotive.com/ Someone in California: https://egge.com/info/water-pump-rebuilding/ What a small world, I know exactly where Egge is we drive by there on my way to my in laws all the time :D . I'm going to wait for my order to come in and see what happens, luckily it's not too much work from what I've seen. Link to comment Share on other sites More sharing options...
Zebvance Posted September 19, 2016 Share Posted September 19, 2016 I had the same problem and did all the research. I came to the conclusion that it is next to impossible replace. I was lucky enough to track down a NOS whole fan hub assembly. Link to comment Share on other sites More sharing options...
big66440 Posted September 19, 2016 Author Share Posted September 19, 2016 I had the same problem and did all the research. I came to the conclusion that it is next to impossible replace. I was lucky enough to track down a NOS whole fan hub assembly. I know some people have done it successfully, . If everything goes to plan I'll post the correct part number necessary for the replacement. The bearing the guy uses in the video has a few bad reviews on Summit and Amazon's website, I do not want want to run a junk bearing which is why I have the NSK 665325 on the way, I already have the NSK 885586 and it won't work on my 89 set up. I hope I can figure this out and help save some people money, I know the dealers ask an arm and a leg for these fan bracket assemblies. Link to comment Share on other sites More sharing options...
big66440 Posted September 26, 2016 Author Share Posted September 26, 2016 Update- I successfully swapped the bearing, I wanted to clarify that either NSK 885586 or 665325 will work !!! the only difference is the length of the shaft on the 885586 is longer but it won't be an issue. I made a mistake and assumed the bearing was pressed out towards the rear of the bracket. The steps to replace it are quite easy,1 use a 3 jaw gear puller to remove the pulley (where the fan clutch bolts on to) from the shaft, 2 press the bearing out using a ball joint press tool ( looks like a big heavy C clamp), 3 press the new bearing in using the same tool you used to press it out, 4 press the fan clutch pulley on with the ball joint press and you're done !! these tools can be found easily at Harbor Freight or they can even be rented from the big auto parts chain stores.I took pictures and I will see if I make a write up on how to replace it if you guys are interested. Link to comment Share on other sites More sharing options...
HOrnbrod Posted September 26, 2016 Share Posted September 26, 2016 Excellent - nice job. That will make a great writeup for the DIY. This might help - just found it. http://www.naxja.org/forum/showthread.php?t=1073406 Link to comment Share on other sites More sharing options...
Zebvance Posted September 26, 2016 Share Posted September 26, 2016 Wow! Great job! Way to do something everyone doubted. Please make a write up so this can be documented. This is one of the few parts that are not made any more, and before you proved wrong, was thought to be a non rebuildable unit. Link to comment Share on other sites More sharing options...
big66440 Posted September 27, 2016 Author Share Posted September 27, 2016 Thanks guys :thumbsup: , I don't have a PC at home but I will upload the pics from my phone to my computer at work and I'll do the write up. Link to comment Share on other sites More sharing options...
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now