Whamm Posted January 3, 2009 Share Posted January 3, 2009 I am replacing the timing chain on the 2.5, and i am down to removing the crankshaft bolt. I cannot seem to break it loose. Just wondering if its a left hand treaded bolt. Thanks for any help. :D Link to comment Share on other sites More sharing options...
mjeff87 Posted January 3, 2009 Share Posted January 3, 2009 "crankshaft bolt", you mean the one that holds the harmonic balancer on the crank snout? It's regular threaded. Easiest way is to bump it with an impact wrench (air or electric). If you don't have access to either, you can wedge a braeaker bar with socket against the framerail and (carefully) bump the engine via the starter (did I mention carefully....) to loosen it, then finish removing with a ratchet. Jeff Link to comment Share on other sites More sharing options...
Whamm Posted January 3, 2009 Author Share Posted January 3, 2009 Yeah the harmonic balancer bolt is the one. Thanks for the info. The write up you did was great on the timing chain replacement. :D But i read it just a little late to think about using the drive accessories to help hold tension for removal of the bolt. :fool: Also glad to know that i don't have to drop the oil pan to replace the tensioner. This is my first timing chain and i am learning as i go. Link to comment Share on other sites More sharing options...
Whamm Posted January 4, 2009 Author Share Posted January 4, 2009 Ok i have a few question now that i have everything apart. I set the timing to TDC by taking the number one spark plug out and bumping the starter until I felt the compession start to build. Then i rotated it to zero using the timing marks on the timing cover. Also the rotor button was pointing to number one post on the cap. So this have been set to TDC correct? But when i removed the timing chain cover the timing marks where incorrect. The piston spocket was correct but the cam spocket was 180 degrees off. Just wondering if i have done anything wrong. Thanks again for any info... Link to comment Share on other sites More sharing options...
Geonovast Posted January 4, 2009 Share Posted January 4, 2009 The cam sprocket can be 180 degrees off. It's supposed to. The crankshaft spins exactly twice as fast as the cam, so every time the crank got to TDC, the cam would turn halfway, 180 degrees. Link to comment Share on other sites More sharing options...
Whamm Posted January 4, 2009 Author Share Posted January 4, 2009 Cool, so does that mean that i rotate the camshaft sprocket around untill it lines up with the crank sprocket timing mark or do time it where it is. :dunno: Link to comment Share on other sites More sharing options...
Geonovast Posted January 4, 2009 Share Posted January 4, 2009 Cool, so does that mean that i rotate the camshaft sprocket around untill it lines up with the crank sprocket timing mark or do time it where it is. :dunno: From what I've seen, with the crank at #1 TDC, the two dots on the sprockets should be pointing straight at each other. Link to comment Share on other sites More sharing options...
mvusse Posted January 4, 2009 Share Posted January 4, 2009 Where they point depends on TDC compression stroke, or TDC exhaust stroke. Which one you need depends on whether the distributor is pointing at #1, or 180 degrees away from it. If the distributor is run off the cam it doesn't matter, if it is run off the crank you have to pay attention. Link to comment Share on other sites More sharing options...
aemsee Posted January 4, 2009 Share Posted January 4, 2009 The dots on the sprockets are to verify valve timing. To set ign timing you need to do what you did with the compression at #1 plug hole. Link to comment Share on other sites More sharing options...
Whamm Posted January 5, 2009 Author Share Posted January 5, 2009 Thanks for the info everyone. I believe i have it back together correctly. We will see tomorrow. Link to comment Share on other sites More sharing options...
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now