White_Comanche Posted December 17 Share Posted December 17 I'd like to know what I'm up against in the future, because I may tackle this project if what I have could become more of an issue. I have noticed that sometimes my clutch pedal feels a bit rough (not entirely smooth) when pressing down on it. To remedy this, my solution has been squirting on some lube onto the clutch Push Rod at the Dust Boot. This stop-gap has worked fairly well. One application was effective for most of the summer. Just this past weekend I got my pickup out, and had to apply again. The pedal was only smooth for about a day (maybe because it's now cold and winter). All the metal moving parts, and the spring of the clutch pedal assembly are thoroughly lubed as well. Transmission is A-OK, and was recently rebuilt a few years ago. There is no "chattering" going on either... just a clutch pedal with subtle, but noticeable roughness. • 1986 2.5L 5-Speed Link to comment Share on other sites More sharing options...
eaglescout526 Posted December 17 Share Posted December 17 Have you taken apart your master cylinder to investigate? I wouldn’t be surprised if the internals are rusting. Link to comment Share on other sites More sharing options...
AZJeff Posted December 18 Share Posted December 18 7 hours ago, eaglescout526 said: Have you taken apart your master cylinder to investigate? I wouldn’t be surprised if the internals are rusting. Agreed. The rod itself only really has contact with the rubber dust boot, which provides almost no friction. The piston and its seals in the mast. cyl. bore, however, will drag massively if the bore or piston are corroded. Link to comment Share on other sites More sharing options...
White_Comanche Posted Wednesday at 03:14 PM Author Share Posted Wednesday at 03:14 PM Guys, no I have not taken apart my Master Cylinder. It probably hasn't been touched in a very long time. I'm a bit apprehensive of bleeding hydraulic fluid because I've not done anything like that before. Would I be able to remove the internal components of the cylinder (spring, plunger, misc bits) from the interior? The 1989 FSM has a section labeled Clutch Cylinder Overhaul, and gives a fairly detailed step by step. Wondering if this would be worth the time, or just go full-hog and purchase an entirely new master cylinder. That would obviously require bleeding, however. Link to comment Share on other sites More sharing options...
eaglescout526 Posted Wednesday at 03:51 PM Share Posted Wednesday at 03:51 PM 32 minutes ago, White_Comanche said: I'm a bit apprehensive of bleeding hydraulic fluid because I've not done anything like that before. It’s brake fluid and it’s pretty easy. Main goal is to have all the air out and any fittings that could let air in addressed and sealed. 32 minutes ago, White_Comanche said: Would I be able to remove the internal components of the cylinder (spring, plunger, misc bits) from the interior? The 1989 FSM has a section labeled Clutch Cylinder Overhaul, and gives a fairly detailed step by step. You could, might be more of a pain than taking it out. You have the easier set up where the bolts are sideways vs the later where it’s an over under set up. 34 minutes ago, White_Comanche said: Wondering if this would be worth the time, or just go full-hog and purchase an entirely new master cylinder. That would obviously require bleeding, however. In my opinion, yes. But seeing how yours is the 84-86 style, i dont know who the OEM manufacture is for that one so this is up to you. Me personally I’d like to just inspect it and see what your up against. Worse comes to worse you get it apart and the bore is pitted to where it’s no longer gonna seal properly, then you’ll get a new one. I think I’ve got one or two of that master cylinder style from the PO of my XJ who went on this rampage to have a stiff clutch pedal. Link to comment Share on other sites More sharing options...
White_Comanche Posted Friday at 09:29 PM Author Share Posted Friday at 09:29 PM I've decided to replace my Clutch Cylinder with a NOS part in the future. I'd like to know which part number to go with... or will both of these work: While searching Mopar Parts Giant with my truck — 1986 Jeep Comanche 2.5L — it comes up with #52000068. Link is down below. However, when I called up my local Chrysler dealership, they came up with #53001163 when they entered the last 8 digits of my VIN. https://www.moparpartsgiant.com/parts/mopar-cylinder-master-clutch-hyd~52000068.html?vin=&make=Jeep&model=Comanche&year=1986&submodel=&extra1=&extra2=&filter=() Link to comment Share on other sites More sharing options...
eaglescout526 Posted Friday at 09:36 PM Share Posted Friday at 09:36 PM I honestly don’t see much of a difference at all. Link to comment Share on other sites More sharing options...
White_Comanche Posted Friday at 10:26 PM Author Share Posted Friday at 10:26 PM Alright, thanks Eagle. Good to know it doesn't matter which one. Link to comment Share on other sites More sharing options...
eaglescout526 Posted Friday at 10:38 PM Share Posted Friday at 10:38 PM The only difference I can speculate is one is just an 84-85 XJ part number and the other is the 86 XJ/MJ combo. But I don’t know for certain. Link to comment Share on other sites More sharing options...
White_Comanche Posted Saturday at 01:36 AM Author Share Posted Saturday at 01:36 AM I'm torn between the two myself, but that XJ/MJ combo sounds logical. If my mind doesn't change I'm leaning towards the #53001163. The guy at the dealership said that is the one he would go for. Question: the NOS I've found never shows the plastic reservoir cup... always just the screw cap. Would I use my current cup on the new one? https://hkresale.com/products/mopar-53001163-master-cylinder-for-brakes-genuine-oem-new-nos-made-by-girling-7 https://www.ebay.com/itm/285386860132 Link to comment Share on other sites More sharing options...
eaglescout526 Posted Saturday at 02:22 AM Share Posted Saturday at 02:22 AM So according to my 84-85 parts book, the 0068 is for the 84 all engines and 85 4cyl 1163 is for the 85 diesel and GM 6. Then in 86 the 1163 is for all engines. Your call, didnt see a difference according to either book. Link to comment Share on other sites More sharing options...
eaglescout526 Posted Saturday at 02:23 AM Share Posted Saturday at 02:23 AM 46 minutes ago, White_Comanche said: Would I use my current cup on the new one? No, as far as I have seen, the 84-86 masters have had that style where it was a cap over the reservoir. Link to comment Share on other sites More sharing options...
White_Comanche Posted Sunday at 12:38 AM Author Share Posted Sunday at 12:38 AM 22 hours ago, eaglescout526 said: according to my 84-85 parts book... Great information. Appreciate you looking up the numbers in your books. Spent the afternoon on a side MJ project, but wanted to put an eye on my clutch cylinder. I was presuming all along that mine was original, but clearly it's aftermarket. Looks like some knucklehead in the past used a pair of pliers to remove and tighten this fitting... instead of a flare nut wrench. Thankfully there's just enough meat left that it can be turned with the proper wrench. Hopefully. I'll get a cylinder ordered and will complete this project sometime soon. Link to comment Share on other sites More sharing options...
eaglescout526 Posted Sunday at 12:58 AM Share Posted Sunday at 12:58 AM Yikes. Love it when folks don’t even try to use the right tool to get something off. Oh well. Hopefully you get it off. If not there’s still a line out there that’s made. Link to comment Share on other sites More sharing options...
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now