jgoodman1988 Posted May 28, 2015 Author Share Posted May 28, 2015 So a little bit of an update, i cleaned the c101, refreshed the grounds, and replaced the map sensor. Test drive went well, but i also went less than a mile, getting a lot of vibration from the driveshaft, think i installed it 180 out when i put the tranny back in. Link to comment Share on other sites More sharing options...
Megadan Posted May 28, 2015 Share Posted May 28, 2015 When you get the chance, remove that C101. Well worth doing. Link to comment Share on other sites More sharing options...
jgoodman1988 Posted May 28, 2015 Author Share Posted May 28, 2015 When you get the chance, remove that C101. Well worth doing. Yea i plan on it, right now i just want it to run right. Got the driveshaft flipped around, drove it and it still drives like crap, so idk, Still gotta look at the cts, cps, and iat. Although i don't think it has anything to do with those sensors. I'm more in line with either distributor or ecm. Link to comment Share on other sites More sharing options...
Katzer Posted July 21, 2015 Share Posted July 21, 2015 Have you had any luck? Mine is back to running like crap again. I have tried everything I can think of. Done all of Cruiser's tips except distributer indexing( not sure I completely understand it). I will let you know if I figure mine out. Link to comment Share on other sites More sharing options...
Katzer Posted July 31, 2015 Share Posted July 31, 2015 Update. After many days of effort, I pulled off the distibutor cap and sprayed it down with WD40. After a few minutes of idling it has stopped the stumbling under load. The cap and rotor look brand new and there are no cracks in it. Going to see how it goes for a few days and see what happens. Link to comment Share on other sites More sharing options...
cruiser54 Posted July 31, 2015 Share Posted July 31, 2015 Man, how humid is it where you live? Link to comment Share on other sites More sharing options...
Katzer Posted August 3, 2015 Share Posted August 3, 2015 Another update. It ran great for about 2 days and the miss has slowly grown worse. It is now so bad again it really can't be driven. I have sprayed WD40 in the distributer again and this time it didn't change the way it runs. I have sprayed down my vacuum lines with throttle body cleaner and I don't think I have any leaks. I am not sure the EGR is working right. I can't ever feel it move when revving the throttle, maybe engine has to under sustained load to open. It has been extremely wet this year and now extremely hot and humid. I can't figure it out. Going to replace coolant temp sensor and attempt to remove Air intake temp sensor (pretty sure this one will just break off). Maybe try to do EGR delete? Getting tired of throwing money at it, but at a loss for what else to try. Replaced the following already Fuel pump fuel filter CPS O2 sensor Plugs and wires Link to comment Share on other sites More sharing options...
LowerEnder Posted January 24, 2023 Share Posted January 24, 2023 On 8/3/2015 at 4:53 PM, Katzer said: Another update. It ran great for about 2 days and the miss has slowly grown worse. It is now so bad again it really can't be driven. I have sprayed WD40 in the distributer again and this time it didn't change the way it runs. I have sprayed down my vacuum lines with throttle body cleaner and I don't think I have any leaks. I am not sure the EGR is working right. I can't ever feel it move when revving the throttle, maybe engine has to under sustained load to open. It has been extremely wet this year and now extremely hot and humid. I can't figure it out. Going to replace coolant temp sensor and attempt to remove Air intake temp sensor (pretty sure this one will just break off). Maybe try to do EGR delete? Getting tired of throwing money at it, but at a loss for what else to try. Replaced the following already Fuel pump fuel filter CPS O2 sensor Plugs and wires Did you ever figure it out? Link to comment Share on other sites More sharing options...
cruiser54 Posted January 24, 2023 Share Posted January 24, 2023 Link to comment Share on other sites More sharing options...
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now