misfitmechanic

Thought I would share this with everybody here. It's a Axial sxc10ii rc truck kit with a proline Comanche body painted to match my full size truck.

Jeepman, I think I have a intake lined up. If it dosent pan out I'll get in touch with you. I think I'm gonna track everything down for the intake swap first then install everything when I do the header.

I've got a 99 intake sitting in my garage that I'll sell you for cheap. I'm not sure what the going rate is but I can send you pictures. I live in Ontario Canada so I doubt it would be a cost effective option. Thanks for the offer though

Well it's a lot better than a kick in the arse

This is a web site that I've got some of my ideas from. http://www.cleggengine.com/downloads/specs/JEEP_4.0_PERFORMANCE_SPECS.pdf

What does the purple line on your chart represent? AFR? I wish the torque curve on your first graph with the intake started at a earlier rpm. From the reading ive done 99+ engine torque peak is around 2800, while a 91 to 95 H.O torque peak is closer to 3800rpm. If possible id love to shift my peak torque to 2800rpm.

12hp isn't a big gain, I was more hoping on " shifting" the peak torque output into a rpm range that I spend more time in.

Ive been doing some reading lately on doing a 99+ intake swap on a earlier 4.0 H.O. and was wondering if its a swap worth doing. Ive got a new header to install and it would make sense to upgrade the intake too. The engine in my Comanche is out of a 91 xj so I would have to find a intake ( duh ), power steering pulley and power steering bracket off a 96 and newer xj. Ive read that the 99+ 4.0 engines make there peak torque output at almost 1000rpm less than the earlier 4.0 H.O and would hopefully compliment the upgraded cam that's already in the engine. Thanks for any info or opinions. Earl

Thanks!

I still haven't had a chance to install this header yet, just got my truck out of winter storage. The washer supplied with my hardware kit are machined with a step in them and I assume this is to account for different flange thickness of the header/intake. Also I wasn't planning on using the supplied gasket as it was kinked during shipping. I was also thinking of getting a couple flanges laser cut out so I didn't have to use the muffler clamps on the y pipe

I ordered the pacesetters this morning. I found a screaming deal on Amazon that I couldn't pass up, about half the price that I could buy them locally and free shipping. One reason I really like the design of these is that they come with a intermediate pipe that goes from the header to the catalytic converter. My current intermediate pipe is a oem style replacement that's not mandrel bent and fairly small diameter. I think this is probably the biggest restriction in my exhaust system. Once these headers show up I think I'll strip off the original paint and then paint them with some sort of high heat header paint. It would be nice to get them ceramic coated but I think that would be a pain to fit, possibly modify them and then have to takem back off to get them coated but I'll see once I get that far. Thanks for all the replys. Earl

I've got my eye on a pacesetter header for my 4.0 ho powered Comanche. Does anybody have any experience, positive or negative with these? I've read some on the net about clearance issues between the collector y pipe and the front driveshaft/front diff yoke. I can't imagine this not being corrected in current production runs. I also wouldn't be too opposed to modifying them if need be for clearence. Thanks for any info. Earl

X 2 on the fuel pump resistor. I had a hard to find hesitation and it turned out to be a bad resistor. It was dropping over nine volts when the truck warmed up.

Hey Altrocker1, where are you from? I just swaped a 4.0l into a mj that originally had a 2.1 turbo diesel. When I bought the truck the engine was missing but I still have lots of other diesel parts. I'm near London Ontario Canada if your interested in any parts. Earl

Same thing, different choice of words