Twin Turbo SN95 Mustang Build

[barimpact]

So I've always been a 4x4 guy growing up, my parents always had trucks and when I started driving I always had a truck, and all my projects were trucks and Jeeps. However, when I started making more car friends in college, I had a group that all had Mustangs (5 or 6 guys). One day they all let me drive their cars on a cruise day and I decided right then and there I had to have one. Since this would be my first sporty car, I looked to find a pretty cheap stang. The stars aligned and 2 days later I happened to come across a guy that was selling all his old stuff to pay off the bank that was repossessing a lot of his stuff, and I got my Mustang for $500.

 

The car is a 1995 Mustang Gt with the 5.0L V8 and the 5 speed manual transmission. Being an old small block Ford, it only made 215 horsepower and 285 torque at the crank when it was new. It was super beat up like it had been a drift practice car. The front driver fender was smashed beyond repair (like it was in a rainstorm of hammers), the driver headlight was a basic sealed beam square that was zip tied in, large pole slide marks on both rear quarter panels, and tires that were dry rotted so bad you could move the car 6-8 inches left and right by pushing on it. The battery was out of a boat. The hood was not latching correctly. Second gear synchro in the transmission was bad. But otherwise, it was a good runner.

 

 

[barimpact]

The absolute first thing I did was get new wheels and tires for the car. I've had my share of junky cars, but the tires on this were the most genuinely unsafe tires I've ever seen on a car, even to this day. The cheap ones I got were off a friend of a friend who got an aftermarket set for his '99 GT. At the same time, my throw out bearing crapped out (2 days after I bought the car). I was living on campus at the time, so me and one of my mustang buddies swapped the bearing AND the transmission in 8 hours on jack stands and oil change ramps with only hand tools in the parking garage at the university. This is one of my best car stories that almost no one believes until they see the evidence.

[barimpact]

Once I got all this done and replacing the horrible air filter (brown and rusty on the outside, blue on the inside. Quite a lot of nasty), I spent some time cleaning up the interior that was actually in good shape.

 

Once I got all this done, it was actually a super good driving car, and it was a ton of fun to hoon around town. Here's a picture of the car next to my daily.

[barimpact]

With the car driving great for a couple months, I decided it's time to add some power. I had just sold an old Powerstroke I had sitting around and in the spur of the moment, I poured basically all of that money into the Mustang to truly make it a project car instead of doing small bolt ons one at a time. With this, I tore down the car and started unbolting pretty much everything from the engine. The main things I purchased for the car are:

 

AFR 185 ported polished heads

Comp Cams 1.6 roller rockers

F303 camshaft

ARP head studs

340 LPH Pump

80 lb injectors

28” Intercooler

Twin T04E Compressor: 55 trim, Turbine: 73 trim

BBK fuel pressure regulator

 

[barimpact]

For a long time, this is how the car sat in the garage. I started getting more into my Jeeps and modifying other projects I had, and since this car had a garage spot, it was put on the backburner. It sat about like this for 2 years

[barimpact]

This is where the car sits currently. COVID-19 has given me a LOT of time to work on the car and get some of the custom stuff done at my shop (such as the intercooler mounting and cutting) and I'm estimating that if all goes well I can get a first start on it next month!