Jump to content
drcomanche

DrComanches Project "Frankenstein" (The Rebuilding)

Recommended Posts

So I've been working on getting the other side of the rail cap off(passenger side), but mostly just for posterity sake, since it had WAY less floor water damage than the drivers side. The floor itself wasn't that bad, but there were some pretty clear rusted out sections, so a little bit of repair ahead.

a64yBTs.jpg

n47lAA1.jpg

The top where it meets. There seems to be a small gap under the brace that allows water to sit. There were rusted holes on both sides of the truck.

ekgm4zO.jpg

 

I also managed to get my skid plate off finally.

X68S7ZL.jpg

Ae5WNtI.jpg

oTxONDI.jpg

LmFJqBT.jpg

And cleaned it up a bit

Sv4iye2.jpg

za3f2HQ.jpg

 

I posted up a topic to see if the rail braces were necessary to put back on, as they are just places for water to sit and cause rust again. I think I'll leave them off for the final build up. I did, however, hit a pretty big snag. 

 

I warn, what you're about to see is painful for us Comanche lovers... Here's a hint

WxmRPdm.jpg

8 to 10 pounds of rust. This is your last chance to stop here...

 

 

So, I always thought that the drivers side was the worse side because of the floor rust, but I was painfully made aware that was not the case. The floor was better off, the rails were far far worse... It's really bad in there, to the point where it's all the way through the top overlap of the frame metal and most of the way through the bottom. I'll let the pictures speak for themselves. I have a lot to consider on possible options to fixing it.

y5iCp3U.jpg

81xzGLC.jpg

jW6Ll8P.jpg

nO2B3sw.jpg

dbsfddw.jpg

MgeNzKK.jpg

JxxS2nL.jpg

SNpGAc3.jpg

PgXFZFj.jpg

3PbjSuX.jpg

There is also a bit up next to the frame splice as well. The metal itself is pretty severely compromised. To the point that it was bent on the bottom of the frame underneath. One good hit would go right through the rail in these spots. The only good thing I can see is that it's pretty much concentrated to the really bad visible spots. Everywhere else on there is fairly solid. I was planning on beefing up the frame anyway, so I guess that's my next step.

 

Share this post


Link to post
Share on other sites

Been a lot of thought going into what to do next, and I've decided that since it's only small portions of the frame and not it's entirety, I'm going to sleeve out the forward section and plate the rest(which I was intending on doing anyway, the timeframe has just been moved up).

 

To start with, I'm removing all the leftover bits of the control arm mount from the frame to get a smooth surface and to get whatever rust may be hiding out. My goal is absolutely no more rust anywhere for the rest of the life of this truck. I'm tired of dealing with new surprises. I finished cutting out the floor to be prepped for new welding and sanded my rails bare with a flap disc. I also broke the old, rusty, and broken nuts out of the framerail(they were definitely replaced at some time because the welds holding them in weren't holding anything). One good whack with a hammer took care of those. I have to find a way to clean out under the braces inside the frame. I know there's still rust hiding under there. I have some questions about the structural pieces on the frame that I'll post over in the tech section. In any case, if this truck wasn't already slated for hardcore tech, it probably will be soon. In plating the frame I will also be mending the seem in the rails where it was just stuck together with spot welds to help build structure.

 

I will also be ditching the torque boxes, as I will be using the rock rail frame attachments for that extra support. I had to remove some of the work that I had payed for, but in this instance, I think simpler is better. Originally, the guys welded quarter inch plate over them, but they were still inaccessible and inconvenient. The less places water can get, and the less complicated it is to reach, the better and easier it will be to maintain. I will be adding three support rails to it that will reach close to flush on the frame and the rails. After everything is attached, I will add L brackets to the rails and will have a bolt on boatside plate. On the inside, I'm not going to spot weld back in the frame brace. It's just asking for more rust and it's simpler to deal without. Any structural weakness should be taken care of by the rock rails, rail braces, and the frame sleeve/plating. I'll make something up for the seat brackets to get them to fit back in. Since I had the trans dropped, I also decided to convert my e brake to the console style. 

 

Removing the lot of these pieces also allows me to clean and repaint them. I repainted my skid plate in green, but started with 2 coats of por 15 since that stuff is tough as nails. It's not perfect looking because of the pitted metal from surface rust, but again, this truck isn't meant to be perfect. I also repainted all the brackets and plates that are for the plate as well. I'm considering welding the outside frame plates onto the rails. I still need to paint the driveshaft and replace all the u joints in it(since they're squeaking quite a bit and who knows how old they are). 

 

I have plenty of touch up welding to do around the truck on bits and pieces that weren't sealed all the way. I'll have to remove the bed again to do so.

 

And now, the pics

BBeMkmD.jpg

The braces I was talking about. Really hard to get under there. Also, the bolts removed.

x6CHuWD.jpg

O5Jcm4l.jpg

Right around where the sleeve is going. That's also the seem I'll be welding.

lUSXdDy.jpg

62J7erN.jpg

Ur8OT3A.jpg

Tbfcr5Z.jpg

aPzV2o4.jpg

jEpgkoY.jpgHB8YFOf.jpg

The Torque boxes removed

1qfOOlh.jpg

1YDZo2X.jpg

1TRTf24.jpg

The ebrake cut in. 

DxarLOz.jpg

QhSMsgB.jpg

Some of the old control arm metal.

VbEWzBa.jpg

D6OjGkt.jpg

dmFDnNX.jpg

EFceTLi.jpg

The skid plate and the extra bits

AMlBDES.jpg

On a side note, if anyone is ever looking for rust or trying to clean the cab, take a moment to cut the filler putty out of the back corners. I had rust hiding under there with no way to tell it was there at all. It all looked sealed up. One side was even rusted through.

 

So the next step now is to get metal from the supply around here, and start making pieces.

Share this post


Link to post
Share on other sites

Been a while since I've posted because I couldn't find a cable that let me drop my photos on the computer. So to begin, I cut out the finger sections of the frame rail joints. After removing the old, rusted, seized nuts from the skid plate/crossmember, I welded in a new set on each side. After a lot of thought on what to do and counting out costs, I decided to go with T&Ms frame stiffener kit for the Comanche. In the overall scheme of things, they were precut with all the reliefs and bent accordingly, which would have been difficult, costly, and time consuming if I had done it myself. I read mixed reviews on them, especially about the fit, but took the chance anyway. During this time, I also managed to grind out the interior of the frame rails really well, and ended up with some severely weakened edges. I dove right in and started cutting the frame rail in sections to clear out the old rot. It was difficult because, as I've said in a post a while ago, the frame has already been spliced and the fish plates overlap the rust(bit of an oversight by the guys who did the repair, since it would have seemed to be an obvious problem, but who knows). Eventually, since I'm not putting the rail caps back in on the floor, I scalped the metal from that(same thickness). Welded it in and then ground the inside real good and hit it with a coat of POR15(I still needed to weld the stiffeners on, but it had been getting water in so I did it as a temporary stopgap). Eventually, I made it to installing the stiffeners and, oh boy, that fit was not good. There were overhangs and misalignments(granted, only with the center section. The rest seem like they'll be way easier) everywhere. I had to hack it up pretty good to get a fit, and hack some more to fit around the existing fish plates. In the end, anything that was an overhang, I cut a shallow ridge across where it should end and hammered it up to get a bit more metal coverage. They turned out alright after some extreme work, with the exception of some odd bends and spots where it had to be "persuaded" to fit. There's also some divots where the weld squares were(very slightly) as, even with a good weld in them, they didn't look good at all, so I did a full fill. I finally finished up the process and am now moving onto putting in the rock rail supports. They will require extra cutting on the bod to get to the rails themselves, since they don't extend all the way to the interior, unfortunately. I'll have 4 supports from the rails to the frame when all is said and done. I have some 3/16 square tube to do the job. Now that I've welded, I have to go in and grind the rails again in the spots where the paint burned off, but all in all, not too bad to do. Then I can start rebuilding the floor sections. I'm going to end up paneling some of the floor but leaving a roughly 30 inch segment of the top of the rails open for later cleaning and access, and just having a 3/16 plate bolted to the top of it. 

 

 In the mean time, I finished out fixing my tail gate. I don't have a press break but I did want the folded edge on the bottom, so I ended up doing it make shift style. I took a wooden dowel and gradually rolled the edge out after clamping it on a 90. It took a while, but eventually, I got it to work pretty well. I then took to welding it on, which, in retrospect, I probably should have done slower, since the metal warped a little bit(although that may have been unavoidable). After that, I started stripping the paint off so I can do the bondo, primer, and paint coats. Ended up with some nice glamour shots of the tailgate in there too. After setting that aside, I went to fixing my seat bracket base. Originally, one of the mounting points had rusted off and was bent. I bent it back, trimmed it out, and with a bit of welding  and some flap disc grinding, got a good piece, if I do say so myself. To avoid weakness, I folded the last tiny bit of it for structure. After welding it in, I drilled a hole through and worked it out with some carbide burrs till it matched the other seat.  

 

I also pulled out my tail lights and turn signals for another idea. I've always been fond of the 2 color scheme I've been working with(Army green and black) so I decided to tint the lenses. This turned out alright. They tinted nicely but getting a good finish was another story, especially since the tail lights have so many angles and ridges to sand. I'll probably end up doing another coat on them when I finish sanding them. The signals turned out very nice, but I may go darker. The plan is to switch all the lights to led. Eventually, I'll also be replacing the headlights with a nice set of leds that has a black out backing. 

 

I purchased new spring isolators, since the old are dry rotted and failing, to install when I go to put on the front stiffeners. 

 

TXQ6uoQ.jpg

The old brace removed to be replaced with steel tube

a2VudMI.jpg

The tail lights all clean

PtV4hti.jpg

One section of frame being repaired

MduovdS.jpg

All the frame stiffeners

0mXhESx.jpg

The lights all tinted

UPX8W2G.jpg

The signals put in for reference. Probably going to go a bit darker though.

LLMrKnE.jpg

7QtIpVH.jpg

The bottom edge of the seat repair

6IGWSnc.jpg

Frame rail all cured(before welding)

9CGU4xq.jpg

The folded edge of the metal for the tailgate

rh5y6AQ.jpg

All lined up

hDAkTaT.jpg

Welding

Tzy9kom.jpg

Stripper doing its thing. It looks worse than it is. 

ULUISEK.jpg

A nice shot of the tailgate after some sanding

fbKSggM.jpg

The seat problem

fbKSggM.jpg

The solution

LIRMs4p.jpg

kSjXOaq.jpg

All done

e627Yei.jpg

xayMmIK.jpg

Welding started

uczXDRw.jpg

Almost done(note, I only just learned welding about half a year ago, so it isn't perfect, but I can guarantee the weld penetration). Just a few touch up bits of pitted metal. The biggest issues I had while welding were: 1. The welder was dying so it cause it to sputter out sometimes and not lay a bead at all. 2. The frame has weak points that were incredibly susceptible to blow through. 3. The overall fit left some things to be desired, but in general, not bad.

 

At this point, the stiffeners for the cab section are on and welded. Now I'm sizing up the tube to frame from the rockers and getting some of the floor pieces cut out and ready to in. Soon, after the frame is painted, I'll bolt the plate back on too. 

 

Share this post


Link to post
Share on other sites

Tip of the cap for continuing on. There’s all too many owners that would’ve walked away by now. :beerchug:

Share this post


Link to post
Share on other sites

Is there anyway you would know the size of the retaining nut the neutral safety switch?  PS awesome job on the truck.

Share this post


Link to post
Share on other sites
1 hour ago, neohic said:

Tip of the cap for continuing on. There’s all too many owners that would’ve walked away by now. :beerchug:

 

damn straight!  I love this build!

Share this post


Link to post
Share on other sites
2 hours ago, jubalb said:

Is there anyway you would know the size of the retaining nut the neutral safety switch?  PS awesome job on the truck.

Thanks. I don't believe I have one on the trans in this, seeing as it's a manual. You may want to pop it into the tech section and see what they say.

 

3 hours ago, neohic said:

Tip of the cap for continuing on. There’s all too many owners that would’ve walked away by now. :beerchug:

It's been some hard times definitely. I'm just glad there wasn't a serious buyer back when I thought I couldn't do anything with it. If it had sold back then, I would've regretted it. 

 

4 minutes ago, JMO413 said:

Amazing build love your commitment! 

Thanks a lot. It's seen some ups and downs, but hopefully I'll actually get to drive it more next spring/summer(We all know I'm going to buy some crazy new thing to install, so the chances are slim)

 

And thanks Pete M. Glad some people like to watch the slow build progress bit by bit.

Share this post


Link to post
Share on other sites

Finally got a good day out to work on the truck today, and while it doesn't seem like much was done, I do feel fairly accomplished. I started creating the guides and cutting out the braces for the rock rail today. I have some 3/16 square tube intended to tie the rails into the overall frame structure that I used. I sized it up using some cardboard guides for the two sides and the top to get as close as I could to the exact dimensions, then cut it out of the tube and did some light sanding for a snug fit. I only managed to do 2 today, but I have to say, it wasn't as difficult as I expected it to be, and I am starting to get really comfortable welding to the point that I'm not grinding or cutting to get a better look. Not bad for  6 months of weld experience, if I do say so myself. I still have one more on this side to get in, but it's in a tough spot, so it will present a bit more challenge than the other 2. After that, it will be held down with 4 welded mounting points and some heavy duty 1/4 plate up front. Should be a very solid setup and replacement for the torque boxes.

 

VXbqeo9.jpg

sCMesyG.jpg

zulrQqJ.jpg

NuEEvRI.jpg

The tube all cut and ground up and placed, ready for welding.

rZ6uj4h.jpg

In  my first weld I only went halfway down and had to do the top half. After that, I just started welding whole sides at a time, which resulted in a much better look.

zS0kGaO.jpg

C0vNzZm.jpg

oRdfvmZ.jpg

The initial fit and weld. I always have trouble welding upside down, but it doesn't look too bad.

I8z59gx.jpg

Here's where I start getting proud. A new welder, a few months of practice, and a decent understanding of the technique makes some alright weld. More practice will only make them better.

8lyhj6S.jpg

ikkiOkn.jpg

All burned in. Time for the forward brace.

 psx2yLk.jpg

I'm not too happy with having to hack up the floor and the inner rocker to do this, and it would have been way easier if it was done when the rails went in, but now I've got to do it, so here goes nothing.

uCRT4No.jpg

LJW6ceU.jpg

cJF8Ik8.jpg

All sized up and tucked in ready for the weld

nFMXWd2.jpg

Both welded in and ready to go.

UV9PB0u.jpg

The spot where the last one needs to go. It's a much smaller distance, but because it's only accessible from underneath, that means I'll have to do the top welds while cramped up under it with a welding helmet that prevents me from getting in close. We'll see how it goes.

 

Share this post


Link to post
Share on other sites

Been a while since I posted on so I thought I'd drop the progress on here. The weather hasn't really been cooperating with me, so I didn't finish as much as I want, but it isn't too bad. Now, I just need to wait for warmer weather so I can bedline everything.

 

From where I left off before, I finished off all of the welding and supports for the rock rails as well as prepping and POR 15 on the insides. I decided to just go completely custom on this build since I think I've shored up the strength on the frame enough that I won't be sacrificing structural support. I had a lot of things I wanted to do, but was concerned over how it would affect everything and I spent so much time thinking over it and getting anxiety that eventually, I just decided screw it, I'm doing it my way, and that's a way that hasn't been done.

 

For starters, rather than try to patchwork the whole interior rocker that had to be cut apart for the supports, I took a piece of 16 gauge and welded an entire reinforcement plate over the entirety of it. This gave it a little more structural strength and was probably the only way to do it cleanly. In the future, I will cut out 2 holes with a holesaw bit so I can access/clean/paint as needed on the inside to keep all of the unnecessarily complex internals from going bad. I rewelded the floor back up, but had to do so in pieces(since it was easier to work around all the cuts I had to make, and it let me use some of my scrap metal) which also meant welding it to the top sections of the rail supports. Because I'm always concerned about the inside of my rails, I decided to go with my earlier thoughts and leave a 34" segment uncovered for future access to the inside. Instead, I welded on some grade 8 bolts through the frame rail edges going up into the cab and cut a 1/4" steel plate as an access panel to get bolted down overtop of it. I did away with the rail cap and kept my floor flat(ter). I've also sanded all of the lower cab up and will be spraying Raptor liner inside the entirety. I'll also carry the bedliner over the door sill to the outside rails of the truck, which will help offroad-proof it a bit better. I cut away my dilapidated firewall mat(the foam on the underside of most of it had turned to dust) in my foot well area. It always managed to get stuck on the pedal and everything in addition to looking bad, so out with it. I left a bit as insulation for the heater underneath it, but the rest will be replaced by some thermal rubberized mats I can stick to it(for whatever doesn't get covered by the liner). All that's left now is painting and bedlining for the interior. I will have to fab up a specialized riser to weld to the 1/4 plate for the seats.

 

I also removed the old transfer case linkage to swap it with a simpler Azzy direct link. It would have been a nightmare to put it back in anyway as it was, and I'm always for simpler is better(i.e. why I got rid of the rail cap and torque boxes for a sealed assembly). I took the time to replace my old trans mount too with an SFR heavy duty one. 

 

I have plenty more parts just sitting by the wayside, waiting for warmer weather, but next week, I'll be starting our heavy workload month(6 days a week, 12 hours a day) so it'll be a while before I post again. My plans for the future, after the frame and interior are situated is 1. convert to a fuel cell system in the bed allowing me to update all the fuel lines and get that squared away. 2. to rerun the exhaust since it's rusted and poorly placed. The plan is to replace everything from the down pipe(maybe the headers too) and incorporate a flex tube to stop the header cracking. The goal is to side pipe it out of a port in the bedside. 3. THOR intake. 4. the rest of the cosmetic upgrades(hood pins and vents, headlights, proper bedlining, repainting the small bits, etc.)

 

bmLX5d3.jpg

Frankenstein getting cold in the snow out here

7ogTFxD.jpg

1qDP1kr.jpg

A few extra looks at the inside. I had to sand it down again and redo some of the POR15 since the welds burned it off in some spots.

cBGRpmr.jpg

WznReGd.jpg

yquioqn.jpg

The floors in all their glory. I ended up having to bend the frame edge up to get a weld under it. Then I just beat it back down to flat.

OPLnH5u.jpg

NLWyzAM.jpg

How the rockers looked before.

YLgQ8bw.jpg

All parts on. Still have to fix those little bottom edges there, but that'll be easy. I do still have to figure a solution for the back of the cab corners that I had to cut into in order to weld those last supports. It's too difficult to access, so I'll just wait until I take the bed off for the fuel system to do that.

0vY3T8A.jpg

After the repaint

09vlp8U.jpg

Bolts in

QwKCUxc.jpg

QJckyiD.jpg

The rockers after, with some panel bits in. It was 16 or 18 gauge for the floor pan pieces, I can't remember, but after all the prep and prime work, it's solid.

y5o2yZd.jpg

kLZVomG.jpgl5sMLAa.jpgPKyMLWK.jpg

WSXUc0w.jpg

Qww1Q7P.jpg

jicZDDE.jpg

Some of the floor work and a finished product after sealing and priming. The seam sealer is a really solid compound, so it'll be sanded a bit smoother before the final. I also need to cut a drain hole up front on both sides.

f4alFR3.jpg

ipYioUv.jpg

DMJWMgC.jpg

mo0QyAL.jpg

HGkrifg.jpg

The plate itself.

jnuGa2A.jpg

Took out all the plates and bits for the bedlining. Going to refurbish the linkage mechanism.

9DSiCrb.jpg

Old vs. New trans mount

CtmqXYb.jpg

K62x4zI.jpg

More parts that aren't on my part shelf(because it's full)

Z3fVJZY.jpg

bxfa51G.jpg

8uwJBYA.jpg

ON5X7fk.jpg

Sanding and matting removed. I'm not finished sanding yet, so it's still very dirty. My blower motor in this thing is going to throwing dust for months after all this work.

Share this post


Link to post
Share on other sites

I like the bolt down rail covers. Easy access later. I may do that when I redo my floor. I think my inner rockers are definitely going to look like yours also. I patched them on my XJ and won't do that again. Total replacement with stronger metal just seems appropriate.

Share this post


Link to post
Share on other sites
On 2/9/2019 at 8:18 PM, Pete M said:

wow, you've been busy!  :L:  looks good!

Thanks, been trying to bring it back for the Spring season, and here I am again with my nose to the grindstone.

 

On 2/9/2019 at 9:25 PM, JMO413 said:

I like the bolt down rail covers. Easy access later. I may do that when I redo my floor. I think my inner rockers are definitely going to look like yours also. I patched them on my XJ and won't do that again. Total replacement with stronger metal just seems appropriate.

I figured since I'm already reinforcing the frame, might as well go all out and make the inside accessible. That's one of the worst spots and if I can make it so I can consistently care for it, I will. As for the inner rockers, for me it was just the easier option than patching. I actually like the look and added bulk too, though, so it worked out.

 

Anyways, here is my big update now that the outage is over and I have time to work on it again. During the outage, I've had a slew of parts arrive for me which include: fuel cell, external fuel pump, fuel lines, hood pins, hood vents, more army green paint, raptor liner, an upgraded t case linkage, brake lines, a new D44 cover gasket, various body plugs, LED headlights, sound mat, a front to back 92 wiring harness, a couple of truck covers, a pillar grab handles(at least that's what they're going to be), a master clutch cylinder, and a new downpipe (to start making my side exhaust). There's probably a few things I forgot, but I'll get to them as I work with them. 

 

I started by disconnecting my gas peddle to remove it and unbolting my clutch master. Since I haven't bench bled the new one yet, so I didn't fully disconnect it. I also managed to get the interior all seam sealed and sanded down, then hit it with a coat of primer. I'll do one more sanding and then prep it up for bedliner, but I'll need a good couple day stretch of nice weather for that. I also started to finish up the underside of the cab, which was it's own complex nightmare of small spaces, weld seams, old rust, and poor positioning. This has bee one of the bigger projects on my plate, since wrapping my head around the project at large, was difficult. There are so many spots where rust could lurk and so many things in the way of getting a good proper prep and paint. Little by little, though, I am tackling it. In the future, in the off chance that I ever have to work on the floors again, I will probably just go with the pre made floor pans to simplify the assembly and finish. For the underside of the cab, I haven't decided if I want to bedline it or not, since I probably won't be able to do all of it. I really want to get the trans tunnel, but the clearance just isn't going to make it possible. 

 

I pulled the bed back off again to access my rock rail edges for bedlining and to stiffen the rear frame. This will, hopefully, be the last time I ever have to drop that gas tank, and I will gain a decent amount of space under the bed in its place. The rock rails are sanded and primed awaiting the aforementioned few nice days(not a common thing here in this season). After pulling the bed, I noticed the back of the cab at the edge seems had a tiny bit of bubbling, so I wire wheeled them out. I'm not sure how moisture made its way in there, but I suppose I'll just have to do a better job this time. 

 

I managed to get lucky with the brake lines for my console emergency brake. I found a few on summit that were on sale for 10 a piece and figured why not give it a try. I hadn't ordered any yet because finding the proper size of the sheath and cable plus the type of ends was practically impossible unless I knew the measurements for a specific car model. I waded through so many listings trying to find the right size, but never did. I bought these on a whim because they looked about right and the measurements were roughly there. I received them and, amazingly, they actually fit with a little modification. I did have to cut the boxed end(not sure what kind of ebrake design it was for, but it didn't fit the gm large), and remove the spring, so it was just a little cylindrical end to fit in the bracket on my calipers that used the already supplied springs. The cables seem strong, so I have high hopes that this will finally solve my issues. 

 

With the nice weather this passed weekend, I also did the bondo work on the tailgate and cab corners. I'm not really going for perfection since it will all be bedlined in the end, but I do want some decently smooth lines. The tailgate got sanded and primed on the bottom today, just to see where the bumps and pits were. Overall, it isn't bad enough to need another run of bondo, which is nice. With that, the rest of the tailgate is ready to prep for paint.

 

Today also allowed me to do some fab work for my trail doors, as I want those for Spring and Summer, too. I finally cut the holes for the half door handles and fit them up with a bit of adjustment. Originally, I wanted to weld a little piece of metal on the end to act as a holder to keep it in the door. When I went to weld, it stuck but didn't feel right. Turns out it was aluminum. Didn't feel light enough to be that, but so be it. I didn't do anything more than superficial damage to it, so I devised another bracket to go behind the handle and screw through the center to hold it in. After getting that to work, I started measuring and fabricating some pull rods to go to the latch. It took some trial and error before I got one that worked perfectly. While I was at it, I also cut all the new hinges to make them removable. Now all that's left is to test fit them, paint them, and adjust the upholstery on the door panels inside. I do have some ideas for a step plate and arm rest cushion, but that will come later. 

 

ZStKIAa.jpg

A pile of goodies(some not shown)

IYKAMRg.jpg

Getting ready to work

378x61Z.jpg

Bed removed, some priming done. I'll have to modify the stiffener a bit before tacking it on.

NPZ3ppL.jpg

The dismantled t case shifter and trans plates I sanded down for paint. I eventually got a few coats on them as well as some on the hood vents.

UNIcTie.jpg

Sizing up some stiffeners

Zfxyg8y.jpg

Sanded some ready for a full prime

5esIiQC.jpg

Full prime. I'll be taking the bedliner up to where the primer is all around the cab

NYB748o.jpg

58Lvxb7.jpg

More primed. Also sanded the patch panels for bondo.

D9eoFI3.jpg

tYDvgEd.jpg

Bondo

Sjxp3iE.jpg

More Bondo

3E753fj.jpg

Some seam sealed underside. It didn't react well with the primer even though it said to use it, so I may have to sand it out a little and do some again.

bP60iWO.jpg

Front drivers side of the cab. Just illustrates the difficulty I'm having pulling it all together.

gcP1a2X.jpg

dLKw3QY.jpg

Tailgate all sanded down.

1bt3IjZ.jpg

7c4y0KX.jpg

And primed. By the way, this primer is terrible. I do not recommend it.

Ek19Epl.jpg

The "modified" brake cable. 

jk6A7c6.jpgSoT754G.jpg

The bracket prototype with the screw hole drilled. Simple but effective.

YGmM0EB.jpg

ZbpvUf1.jpg

In the door

oyz4RY4.jpg

The custom latch rods, the top one ended up being the winner. It is a bit more flexible, but also has the tiniest bit more range of movement that allowed fully engaged and disengaged function. 

tXkXCCc.jpg

And lastly, all the pieces

 

Share this post


Link to post
Share on other sites

And back with another update. I will be doing this very often for the next few months as I push to get the truck ready for show and trail season. 

 

This is a smaller update to cover the daily progress I've managed. Today, my goals were twofold. I wanted to finish the welding under the cab so that I could finally finish sealing it up and painting. As I said before, it's one of the more difficult bits. But today, I finally managed to pull myself into doing it. The main problem was that I needed to weld some new  bridge pieces where I cut out for the rock rails so there weren't gaping holes in my rockers. The fit was difficult, to say the least, and I put it off because I knew it would be a job without a lot of progress to show. But finally, it is done. No more welding under the cab(for now). All that's left is to seam seal and paint it up. 

 

In addition, I also managed to test fit one of the trail doors, and I'm really excited for when those will be done. It fits up well, I just need to get hinges that work for me. I have a handful that I was cutting and dismantling to put on the doors, but some were simply impossible to work the pin loose. Otherwise, all that remains is to cut the hole for the other door to have a handle and then its finish work. I'll have to sand and prime the doors as well as spray the inside, just to be sure it doesn't rust. Then it goes to paint with the tailgate and hood vents. After that, I'll work the door panels I have and cut them to fit and look like a stock addition.

 

With all that out of the way, I'll probably start prepping the frame rear for stiffeners.

 

TEjOJKv.jpg

Did a full prime of the tailgate too. There's a lot of high and low spots from the old paint I'll have to sand out.

YxvSWs0.jpg

aR3hGil.jpg

The finished bits, ready for seam seal and paint.

dmnYlsu.jpgOJxZqvv.jpg

6LJ3KgH.jpg

Took out the headlights and started pulling the fenders off. I'll be custom making a 3/16 plate to stabilize the hinges soon, so it all comes off. I'll also be replacing the headlights.

KRfiIM7.jpg

uTuIOtN.jpg

ufSOSue.jpg

And finally, the trail door in position for a final check

Share this post


Link to post
Share on other sites

I managed to get a little bit more done and the truck is fighting me every step of the way. I have a good three page list going that I'm trying to finish in 2 months so I can take the truck out to a big offroad show around here, so I'm really pushing to get things done. 

 

I removed the fenders and fabbed up some brace plates for the hinges and got those welded on. The welds to the hinges themselves were perfect, but the welds to the metal just didn't want to cooperate. Whether it was blowing through, not welding to it, or just spitting air out from behind the plate through the molten metal, it really didn't want those plates to go on. But persistence won out in the end and they are all on and primed. I also wire wheeled the drivers side rear rail and started welding that on. And that, too, is also fighting me. Some welds are fine but any welds around the support ridge in the side just won't stick. I fiddle with the numbers on the welder and then I'm melting it through. One way or another, it will get finished, though. I had to trim the stiffeners quite a bit for something that was supposed to be created for the truck. I also had to do some trimming for the fish plate and rock rail support. Eventually I'll get to sanding and painting it up with POR 15, but I'll have to regrind the inside of the rails since most of the paint will be burned off from the welds. 

 

The rocker panels now have 1.5" holes I cut for access to paint and check up on it, and I added drain holes in the floor. I pulled a plastic plug out from under my dash area for prep and noticed it said CAPLUGS on it, so I looked them up in the hope of finding some more in different sizes, and I did, so I bought a ton for all the little holes all around. The inside is all taped up for the liner, but I'm still waiting for a day to do it(it's pretty rainy here). I finished out the cuts on the other door and fabbed the support plate for the handle, so now it's on to customizing the door panels. I finished up all the sealing under the cab, so it is also ready for paint and while I was at it, I scraped the oil dirt from the underside of the trans tunnel so I can get that painted up too. 

 

gYheXir.jpg

The cuts to piece it around my supports

h8hUbSq.jpg

Fenders off

xoY9eOx.jpgGpaOPF2.jpg

Lk5NCqc.jpgPTXmQ8Q.jpg

lfrhp5l.jpgGLwHqKr.jpg

The hinge plates. I will also have to customize some hinge pins, since I can't find any anywhere, but I made sure it was grade 5 hardware

d7ikpS0.jpg

Holes cut

kZYtXbs.jpg

Taped up

NwaiIM9.jpg

3K87vXW.jpg

bomS3cN.jpg

MwvgTRK.jpg

cRTjHCf.jpg

ap1VIuA.jpg

Welding in progress

Cmx0O6L.jpg

jWJcLFc.jpg

And the other side all ground off. I am a little sad I was grinding off a perfectly good POR 15 job, but it's all for the better.

Aep9RsP.jpgQI19tkC.jpg

8d8lH0V.jpg

And all scraped off and ground as far up as I could get it. I removed the fuel lines and the exhaust for some added room. The exhaust was a pita and I'm honestly surprised I didn't strip the bolts.

I9zt4IC.jpg

And handle in.

HMTsf2p.jpg

And another little gift I got for myself. It is't mounted up yet since once I get to the front, the bumper is coming off to be bedlined.

i6EhzZY.jpg

Started sanding. (I had a lot of downtime between weld periods)

Share this post


Link to post
Share on other sites

Ok, progress seems slow right now if only because I'm spending a good 8 to 12 hours welding these stiffeners. Now, for anyone who is considering frame stiffeners, I have a few pointers... Don't. Just don't. Sure, it makes the frame more sturdy, but they didn't fit hardly at all. Tons of time in trimming and grinding to get all the edges right and holes accounted for. Then the welding... Oh god, the welding. The frame is a fickle mistress, and sometimes the weld will be great, but for seemingly no reason, it will not hold, or won't adhere, or sometimes, just blow holes in the welds. I thought that these rear ones couldn't possibly be more difficult than the cab ones, and while they did, indeed, take less trimming, they are still a nightmare.

 

So that said, I have just about finished one side of the rear. It's all welded up, it just needs some touch up weld to get the kinks smoothed out. Unfortunately, the ridge section just didn't cooperate, so it definitely doesn't look its best. I'll have to take some time trimming it up to make it look better. I'm almost done with the passenger side as well, which went much easier(to some degree). I will still have to grind and touch it up. 

 

I also finished up the bottom of the cab. All the seams are sealed and it's ready for paint, which will be POR15. I also finished up the door panels for the interior. All I have to do is drill the holes for the panel tabs on the metal. I have finished sanding and priming the outside bits of one door. And I started grinding out the tailgate, since the old paint just couldn't be smoothed over.

 

I finished out putting the vibration mat in the cab as well. I may add more in a couple places though.

 

aLebfDO.jpg

NLkXNNK.jpg

wi3TJCy.jpg

KrerZBp.jpg

The rail getting welded. And the almost finish on the other side. 

cFYmteP.jpg

J3Oa4az.jpg

The sound and heat mat

1rsBkqh.jpg

Door panel before sticking it together

wYRuvPF.jpg

xXTrESV.jpg

7PTK5ub.jpg

The panels being stuck together.

GwmmCCB.jpg

And a little shot of the bolt strips I'll be welding on to each side for the bolt on boatside plates.

 

Again, there has been a lot more work than it seems, but once I finish the welding, it should wrap up faster.

 

Share this post


Link to post
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.


×
×
  • Create New...