Jump to content
Sign in to follow this  
chicofuentes0224

RTV on water pump gasket?

Recommended Posts

Iv always used rtv or my favorite is "the right stuff" but iv gotton used to using gaska cinche and i recomend using it more than anything else . it won't weld the gaskets to there mating surfaces and makes clean up a breez and i have never had a problem using any of the above products aslong as u use them very sparingly

Share this post


Link to post
Share on other sites

Another person another opinion. I prefer Anti-Seize on most gaskets. If it is rubber- I prefer Food grade. On all others I use Bostik Never Seez.

Share this post


Link to post
Share on other sites

I don't think it needs RTV from what I remember. I'm 99% sure I put the last one on dry. Which in retrospect was kinda stupid. Normally I'd throw crisco on it... Then it's reuseable.

Share this post


Link to post
Share on other sites
I don't think it needs RTV from what I remember. I'm 99% sure I put the last one on dry. Which in retrospect was kinda stupid. Normally I'd throw crisco on it... Then it's reuseable.

 

You're kidding...right?

 

Another person, another opinion: I always use RTV on gaskets. Yes, it destroys them if you have to remove the part, but if the mating surfaces have a small irregularity the RTV can make the difference. If you crank down on the mounting bolts to force the gasket itself to close up a small irregularity can crack the housing.

Share this post


Link to post
Share on other sites
I don't think it needs RTV from what I remember. I'm 99% sure I put the last one on dry. Which in retrospect was kinda stupid. Normally I'd throw crisco on it... Then it's reuseable.

 

You're kidding...right?

 

Another person, another opinion: I always use RTV on gaskets. Yes, it destroys them if you have to remove the part, but if the mating surfaces have a small irregularity the RTV can make the difference. If you crank down on the mounting bolts to force the gasket itself to close up a small irregularity can crack the housing.

 

Hey this is Dirty,,, you did read his signature right? jamminz.gif

Share this post


Link to post
Share on other sites

I like Right Stuff as well, but I have never used any type of sealer on a 4.0L water pump and I have changed a few. The only gaskets I have ever put any kind of sealer on were cork gaskets. If you have a rubber gasket on something...there is definitely no need for sealer.

Share this post


Link to post
Share on other sites

I've always used white lithium grease on cooling system gaskets not for

the reusing of the gasket but I was taught that rtv was bad for the water

pump not sure why but to each is own

 

-T.J.-

Share this post


Link to post
Share on other sites
I don't think it needs RTV from what I remember. I'm 99% sure I put the last one on dry. Which in retrospect was kinda stupid. Normally I'd throw crisco on it... Then it's reuseable.

 

You're kidding...right?

 

 

No, not at all. But I've never crisco'd a water pump gasket yet. I should have on the last one I did, I just wasn't really thinking right or in the mood. However, normally I do it to EVERY felt gasket. They'll still seal fine, but when you take it apart it'll just fall out and look near as good as new. I'm not saying I intend to reuse the gasket until the end of time (eventually it'll degrade), but if I had to pull the water pump for some reason (or far more likely, the t-stat housing) I would not have to have a spare gasket on me.

 

We do it on the aircraft ALL the time. For a lot of maintenance you have to pull components that are not related to what you're doing. And if the gasket crumbles when you do it and you're in some god-forsaken place without a spare, you ain't going anywhere until a spare gets flown in.

Share this post


Link to post
Share on other sites

for my stroker I coated both side with a thin coat, and let it dry. Then I installed it. It does not leak. I figure it will let it mold to the irregularities a little better, without all the clean up if I pop the pump. 12k miles so far.

 

I usually tell people to RTV it to the block if they are installing it while the engine is in the truck. That way you do not have to worry about the gasket getting out of place during install.

Share this post


Link to post
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
Sign in to follow this  

×